LIS3DSH x y z axis is incorrect - c

Question

I have tried to work with LIS3DSH sensor using SPI protocol. I applied procedures on STM32L0 Discovery kit LoRa. But it didn't work.
My problem is The LIS3DSH x-y-z-axis output value is invalid and the value is not changed. No matter which direction I rotate the device but I check ID of LIS3DSH is correct ( 0011 1111)
Component
STM32L0 Discovery kit LoRa
LIS3DSH (https://www.amazon.com/LIS3DSH-High-Resolution-Three-axis-Accelerometer-Triaxial/dp/B07QS5D9K9/ref=sr_1_4?dchild=1&keywords=LIS3DSH&qid=1615701212&sr=8-4)
init SPI2
...
void HW_SPI2_Init(void)
{
/*##-1- Configure the SPI2 peripheral */
/* Set the SPI parameters */
hspi2.Instance = SPI2;
hspi2.Init.BaudRatePrescaler = SpiFrequency(10000000);
hspi2.Init.Direction = SPI_DIRECTION_2LINES;
hspi2.Init.Mode = SPI_MODE_MASTER;
hspi2.Init.CLKPolarity = SPI_POLARITY_LOW; // CPOL = 0
hspi2.Init.CLKPhase = SPI_PHASE_2EDGE; // CPHA = 1
// hspi2.Init.CLKPhase = SPI_PHASE_1EDGE; // CPHA = 0
hspi2.Init.DataSize = SPI_DATASIZE_8BIT;
// hspi2.Init.DataSize = SPI_DATASIZE_16BIT;
hspi2.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB;
hspi2.Init.NSS = SPI_NSS_SOFT;
hspi2.Init.TIMode = SPI_TIMODE_DISABLE;
hspi2.Init.CRCPolynomial = 10;
SPI2_CLK_ENABLE(); // Enable clock for SPI 2
if (HAL_SPI_Init(&hspi2) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/*##-2- Configure the SPI GPIOs */
HW_SPI2_IoInit();
}
...
initialization LIS3DSH
void HW_SPI2_IoInit(void)
{
GPIO_InitTypeDef initStruct = {0};
initStruct.Mode = GPIO_MODE_AF_PP;
initStruct.Pull = GPIO_PULLUP ;
initStruct.Speed = GPIO_SPEED_FAST;
initStruct.Alternate = SPI2_AF;
HW_GPIO_Init(LIS3DH_SCLK_PORT, LIS3DH_SCLK_PIN, &initStruct);
HW_GPIO_Init(LIS3DH_MISO_PORT, LIS3DH_MISO_PIN, &initStruct);
HW_GPIO_Init(LIS3DH_MOSI_PORT, LIS3DH_MOSI_PIN, &initStruct);
initStruct.Mode = GPIO_MODE_OUTPUT_PP;
initStruct.Pull = GPIO_NOPULL;
HW_GPIO_Init(LIS3DH_NSS_PORT, LIS3DH_NSS_PIN, &initStruct);
HW_GPIO_Write(LIS3DH_NSS_PORT, LIS3DH_NSS_PIN, 1);
}
CS ON or OFF
void HW_SPI2_CS_ON (void)
{
HW_GPIO_Write(LIS3DH_NSS_PORT, LIS3DH_NSS_PIN, 0);
}
void HW_SPI2_CS_OFF (void)
{
HW_GPIO_Write(LIS3DH_NSS_PORT, LIS3DH_NSS_PIN, 1);
}
Read ID
uint8_t LIS3DSH_DH_CHECK_ID (void)
{
uint8_t addr = LIS3Dx_WHO_AM_I_ADDR | LIS3Dx_READ;
HW_SPI2_CS_ON();
HW_SPI2_SPI_1byte_Write_and_Read(addr);
HW_SPI2_CS_OFF();
UsingTypeint_LIS3DSH_DH.ID = au8BufferRead_SPI2[0];
return UsingTypeint_LIS3DSH_DH.ID;
}
Read X axis ( only) (Incorrect)
void LIS3DSH_DH_GET_XYZ (void)
{
uint8_t addr = LIS3Dx_OUT_X_L_ADDR | LIS3Dx_READ ;
HW_SPI2_CS_ON();
HW_SPI2_SPI_1byte_Write_and_Read(addr);
HW_SPI2_CS_OFF();
addr = LIS3Dx_OUT_X_H_ADDR | LIS3Dx_READ ;
HW_SPI2_CS_ON();
HW_SPI2_SPI_1byte_Write_and_Read(addr);
HW_SPI2_CS_OFF();
}
HW_SPI2_1byte_Write_and_Read
bool HW_SPI2_SPI_1byte_Write_and_Read(uint8_t u8Address)
{
if(HAL_SPI_Transmit(&hspi2, (uint8_t *)&u8Address, 1, HAL_MAX_DELAY) == HAL_OK){
if(HAL_SPI_Receive(&hspi2, (uint8_t *)&au8BufferRead_SPI2[0], 1, HAL_MAX_DELAY) == HAL_OK){
return true;
}
}
return false;
}
Signal
output X L
output X H

Answer 1

Am not sure if you are using the state machine and register accesses of the LIS3DSH accurately.
As a reference see the register mapping in https://github.com/STMicroelectronics/stm32-lis3dsh/blob/main/lis3dsh.h (start at line 95) and the code in https://github.com/STMicroelectronics/stm32-lis3dsh/blob/main/lis3dsh.c
The function that actually writes and reads the SPI bus is void ACCELERO_IO_Write(uint8_t *pBuffer, uint8_t WriteAddr, uint16_t NumByteToWrite) and void ACCELERO_IO_Read(uint8_t *pBuffer, uint8_t ReadAddr, uint16_t NumByteToRead)
This is defined in https://documentation.help/STM32F4-Discovery-BSP/stm32f4__discovery_8c_source.html at lines 560 and 594
In void ACCELERO_IO_Write(uint8_t *pBuffer, uint8_t WriteAddr, uint16_t NumByteToWrite) the actual SPI write is done at lines 574 to 582
00574 SPIx_WriteRead(WriteAddr);
00577 while(NumByteToWrite >= 0x01)
00578 {
00579 SPIx_WriteRead(*pBuffer);
00580 NumByteToWrite--;
00581 pBuffer++;
00582 }
(as always with SPI first activate register, then write data...)
In SPIx_WriteRead(WriteAddr); the WriteAddr is taken from the register mapping in https://github.com/STMicroelectronics/stm32-lis3dsh/blob/main/lis3dsh.h, start at line 9
(the above code by STM for the LIS3DSH is nice work, this implementation is very clean and structured)
The datasheet of the LIS3DSH is in https://www.st.com/resource/en/datasheet/lis3dsh.pdf, the reference manual is far more detailed it is in https://www.st.com/resource/en/application_note/dm00026768-lis3dsh-3axis-digital-output-accelerometer-stmicroelectronics.pdf it also includes explanation of the state machines, that have to be configured before the device works