I am trying to send AT commands to a Telit modem from C. Simply interfacing with the modem through system() calls works fine, but there are some issues that arise when I try to transfer a python script with AT#WSCRIPT. The ">>>" portion also gets transferred into the chip, corrupting the script.
Anyway, so I am now trying to do it within C using termios library. The problem is, I can only send the chip one "AT" command, it responds with an OK and every attempt to send another AT commands results in an ERROR response. Further, after runnning my C code, I can't interface with the chip even through the terminal.
I suspect something is off about the termios configuration, which is listed below.
Any ideas? Thanks
char command[] = "AT\r\n";
fd = open(serialport, O_RDWR | O_NOCTTY | O_NDELAY);
termios_config.c_cflag &= ~PARENB;
termios_config.c_cflag &= ~CSTOPB;
termios_config.c_cflag &= ~CSIZE;
termios_config.c_cflag |= CS8;
termios_config.c_cflag &= ~CRTSCTS;
termios_config.c_cflag |= CREAD | CLOCAL;
termios_config.c_cflag &= ~(IXON | IXOFF | IXANY);
termios_config.c_cflag &= ~(ICANON | ECHO | ECHOE | ISIG);
termios_config.c_cflag &= ~OPOST;
tcsetattr(fd, TCANOW, &termios_config);
write(fd, send_str, strlen(send_str));
Related
I am trying to read data from serial port sent by RS232 module using :
A USB - SERIAL converter
A C program and the lib TERMIOS (Which worked perfectly ; I can read and send data in real time).
A Linux environment
Now, I'm trying to do the exact same thing but using directly the serial port of my device and not the USB port.
With the same configuration (except I change the device from tty USB0 to tty mxc2 and using a RS232 cable only not the USB - SERIAL converter). I can't get the data but when I unplug the RS232 cable, all the data I try to read is received and printed to the terminal.
I also tried to use stty directly to read (thinking it was a C problem) but I get the same result (I unplug the RS232 cable & the data is read)
I can not explain why there is a delta between using USB - RS232 converter and using only RS232 cable.
//configuration of TERMIOS :
tty.c_cflag |= (CLOCAL | CREAD); /* ignore modem controls */
tty.c_cflag &= ~CSIZE;
tty.c_cflag |= CS8; /* 8-bit characters */
tty.c_cflag &= ~PARENB; /* no parity bit */
tty.c_cflag &= ~(CSTOPB | CRTSCTS); /* only need 1 stop bit & no hardware flowcontrol */
/* setup for non-canonical mode */
tty.c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP | INLCR | IGNCR | ICRNL | IXON);
tty.c_lflag &= ~(ECHO | ECHONL | ICANON | ISIG | IEXTEN);
tty.c_oflag &= ~OPOST;
tty.c_cc[VMIN] = 0;
tty.c_cc[VTIME] = 0;
//trying to read with termios :
retlen = read(fd,&tmp_buff,1);
if (retlen > 0)
printf("%02x\n",tmp_buff);
here are some result and output from terminal that may help :
When the cable is plugged the data are not displayed
root#2021ufv6zgzg:~# ./main.exe
When the cable is unplugged the data are displayed
root#2021ufv6zgzg:~# ./main.exe
00
fe
00
fe
00
fe
00
fe
Same goes with only stty, data displayed when I unplug the cable :
od -x < /dev/ttymxc2
0003260 fe00 fe00 fe00 fe00 fe00 fe00 fe00 fe00
Thank you very much for your help. Even though you can not find the solution, i'd really like to know the differences between using tty USB0 and tty mxc2.
I have written a program in C to communicate with a 3G modem connected to my raspberry pi over serial uart. After it's open, I do not break the connection unless the program crashes. It runs fine when I run it myself, but when I create a service to run it, it fails right after it starts.
My main question, is this an issue with my program, or is this an issue with how I configured my linux service to run? And what is the best practices to fix this.
my service file
[Unit]
Description=Firmware for sensor IOT module
Documentation=m.thompson.239#gmail.com
After=network-online.target
[Service]
Type=simple
ExecStart=/hdd/firmware
StandardOutput=syslog
RestartSec=30
Restart=always
[Install]
WantedBy=multi-user.target
Alias=firmware.service
When I check the status of the service
Loaded: loaded (/lib/systemd/system/firmware.service; enabled; vendor preset:
Active: activating (auto-restart) (Result: signal) since Thu 2018-07-12 14:44
Process: 539 ExecStart=/hdd/firmware (code=killed, signal=SEGV)
Main PID: 539 (code=killed, signal=SEGV)
Jul 12 14:44:34 raspberrypi systemd[1]: firmware.service: Failed with result 'si
lines 1-7/7 (END)...skipping...
● firmware.service - Firmware for sensor IOT module
Loaded: loaded (/lib/systemd/system/firmware.service; enabled; vendor preset: enabled)
Active: activating (auto-restart) (Result: signal) since Thu 2018-07-12 14:44:34 UTC; 28s ago
Process: 539 ExecStart=/hdd/firmware (code=killed, signal=SEGV)
Main PID: 539 (code=killed, signal=SEGV)
Jul 12 14:44:34 raspberrypi systemd[1]: firmware.service: Failed with result 'signal'.
These are my setting when I open the serial port.
int set_interface_attribs(int fd, int speed)
{
struct termios tty;
if (tcgetattr(fd, &tty) < 0) {
printf("Error from tcgetattr: %s\n", strerror(errno));
return -1;
}
cfsetospeed(&tty, (speed_t)speed);
cfsetispeed(&tty, (speed_t)speed);
tty.c_cflag |= (CLOCAL | CREAD); /* ignore modem controls */
tty.c_cflag &= ~CSIZE;
tty.c_cflag |= CS8; /* 8-bit characters */
tty.c_cflag &= ~PARENB; /* no parity bit */
tty.c_cflag &= ~CSTOPB; /* only need 1 stop bit */
tty.c_cflag &= ~CRTSCTS; /* no hardware flowcontrol */
/* setup for non-canonical mode */
tty.c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP | INLCR | IGNCR | ICRNL | IXON);
tty.c_lflag &= ~(ECHO | ECHONL | ICANON | ISIG | IEXTEN);
tty.c_oflag &= ~OPOST;
/* fetch bytes as they become available */
tty.c_cc[VMIN] = 1;
tty.c_cc[VTIME] = 1;
if (tcsetattr(fd, TCSANOW, &tty) != 0) {
printf("Error from tcsetattr: %s\n", strerror(errno));
return -1;
}
return 0;
}
I want to read data from UART, i followed this tutorial, the write function works as expected, however i'am getting problem with the read function :
This is the uart_init function:
void uart_init()
{
printf("\n +----------------------------------+");
printf("\n | Serial Port Write |");
printf("\n +----------------------------------+");
/*------------------------------- Opening the Serial Port -------------------------------*/
fd = open("/dev/ttyUSB0",O_RDWR | O_NOCTTY| O_SYNC); /* !!blocks the read */
/* O_RDWR Read/Write access to serial port */
/* O_NOCTTY - No terminal will control the process */
/* O_NDELAY -Non Blocking Mode,Does not care about- */
/* -the status of DCD line,Open() returns immediatly */
if(fd == -1) /* Error Checking */
printf("\n Error! in Opening ttyUSB0 ");
else
printf("\n ttyUSB0 Opened Successfully ");
/*---------- Setting the Attributes of the serial port using termios structure --------- */
struct termios SerialPortSettings; /* Create the structure */
tcgetattr(fd, &SerialPortSettings); /* Get the current attributes of the Serial port */
cfsetispeed(&SerialPortSettings,B19200); /* Set Read Speed as 19200 */
cfsetospeed(&SerialPortSettings,B19200); /* Set Write Speed as 19200 */
SerialPortSettings.c_cflag &= ~PARENB; /* Disables the Parity Enable bit(PARENB),So No Parity */
SerialPortSettings.c_cflag &= ~CSTOPB; /* CSTOPB = 2 Stop bits,here it is cleared so 1 Stop bit */
SerialPortSettings.c_cflag &= ~CSIZE; /* Clears the mask for setting the data size */
SerialPortSettings.c_cflag |= CS8; /* Set the data bits = 8 */
SerialPortSettings.c_cflag &= ~CRTSCTS; /* No Hardware flow Control */
SerialPortSettings.c_cflag |= CREAD | CLOCAL; /* Enable receiver,Ignore Modem Control lines */
SerialPortSettings.c_iflag &= ~(IXON | IXOFF | IXANY); /* Disable XON/XOFF flow control both i/p and o/p */
SerialPortSettings.c_iflag &= ~(ICANON | ECHO | ECHOE | ISIG); /* Non Cannonical mode */
SerialPortSettings.c_oflag &= ~OPOST;/*No Output Processing*/
/* Setting Time outs */
SerialPortSettings.c_cc[VMIN] = 10; /* Read at least 10 characters */
SerialPortSettings.c_cc[VTIME] = 0; /* Wait indefinetly */
if((tcsetattr(fd,TCSANOW,&SerialPortSettings)) != 0) /* Set the attributes to the termios structure*/
printf("\n ERROR ! in Setting attributes");
else
printf("\n BaudRate = 19200 \n StopBits = 1 \n Parity = none");
}
the receive function :
void uart_receive()
{
char read_buffer[32]; /* Buffer to store the data received */
int bytes_read = 0; /* Number of bytes read by the read() system call */
int i = 0;
bytes_read = read(fd,&read_buffer,10); /* Read the data */
printf("\n\n Bytes Rxed %d", bytes_read); /* Print the number of bytes read */
printf("\n\n ");
for(i=0;i<bytes_read;i++) /*printing only the received characters*/
printf("%c",read_buffer[i]);
printf("\n +----------------------------------+\n\n\n");
}
the main function :
void main(void)
{
uart_init();
/*------------------------------- Write data to serial port -----------------------------*/
//uart_write_commande(write_buffer); //Write function works well
uart_receive();
close(fd);/* Close the Serial port */
}
I execute the program and wait for data bytes to be received in UART, i send data using UART but the read function keeps blocked.
I'am using a Virtual machine with Ubunutu 14.04 on it, and i'am not sure that using an emulated UART can cause problems during reception.
Your program is hanging in the read() syscall because it is blocked waiting for a line-termination character.
You tried to configure the port for non-canonical mode with the statement
SerialPortSettings.c_iflag &= ~(ICANON | ECHO | ECHOE | ISIG); /* Non Cannonical mode
but that operation is on the wrong termios element.
The ICANON attribute is part of the lflag element (and not the iflag). (This error originates from the tutorial you referenced!)
Therefore your program is performing blocking canonical reads.
There's a convenient termios function for configuring non-canonical mode:
cfmakeraw() sets the terminal to something like the "raw" mode of the old
Version 7 terminal driver: input is available character by
character, echoing is disabled, and all special processing of
terminal input and output characters is disabled. The terminal
attributes are set as follows:
termios_p->c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP
| INLCR | IGNCR | ICRNL | IXON);
termios_p->c_oflag &= ~OPOST;
termios_p->c_lflag &= ~(ECHO | ECHONL | ICANON | ISIG | IEXTEN);
termios_p->c_cflag &= ~(CSIZE | PARENB);
termios_p->c_cflag |= CS8;
There's an error in the read function
bytes_read = read(fd,&read_buffer,10); /* Read the data
should be
bytes_read = read(fd,read_buffer,10); /* Read the data
Your read() function may be blocked, for whatever reason. Here is a discussion on reading from a serial port, including code for blocked/unblocked settings.
It may also be possible that there is no data being transferred, leading to nothing being read. Without having access to the hardware setup, it is difficult to go further without very specific information about what you are seeing.
Also, in addition to passing the read_buffer correctly (another answer), there are at least two additional things that may improve:
1) check the return of read before using it:
bytes_read = read(fd,&read_buffer,10); /* Read the data*/
if(bytes_read > 0)
{
...
}
2) Change:
for(i=0;i<bytes_read;i++) /*printing only the received characters*/
printf("%c",read_buffer[i]);
To:
//after successful read:
read_buffer[bytes_read]=0;//place null termination after last character read.
printf("%s",read_buffer);//note format specifier
This will print the number of characters read, without the loop.
I have the following set up: a computer that runs Linux (TCL) and device that sends packets of fixed length (10 bytes) with fixed frequency (100 Hz).
On computer, i have that serial port open, and i am trying to read incoming data. However, instead of recieving it in 10-byte chunks all the time, lesser amounts of data are being read, and i am forced to reassemble them back.
My goal is to send a responce for each packet once it arrives, preserving intervals between packets as much as possible.
This is how i open the serial port:
int fd = open(device_name, O_RDWR | O_NOCTTY | O_NONBLOCK);
if(fd == -1)
{
LOGPRINT("Failed to open terminal file.\nError #%d (%s)\n",
errno, strerror(errno));
return fd;
}
LOGPRINT("Setting terminal attributes\n");
struct termios config;
struct termios *pterm = &config;
// set baud rate
LOGPRINT("Setting baud rate to %d.\n", baud_rates[baud_rate_index]);
// change to raw mode
LOGPRINT("Setting terminal to raw mode\n");
pterm->c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP | INLCR
| IGNCR | ICRNL | IXON);
pterm->c_oflag &= OPOST;
pterm->c_lflag &= ~(ECHO | ECHONL | ICANON | ISIG | IEXTEN);
cfsetispeed(pterm, baud_bits[pconfig->baud_rate_index]);
cfsetospeed(pterm, baud_bits[pconfig->baud_rate_index]);
LOGPRINT("Set character size, parity and stop bit flags.\n");
// set character size
pterm->c_cflag &= ~CSIZE;
pterm->c_cflag |= csize_flag;
// set parity
pterm->c_cflag &= ~(PARENB | PARODD);
pterm->c_cflag |= parity_flag;
// set stopbits
pterm->c_cflag &= ~CSTOPB;
pterm->c_cflag |= stopbits_flag;
// enable reading; ignore control lines
pterm->c_cflag |= CREAD | CLOCAL;
// disable flow control
pterm->c_cc[VMIN] = 1;
pterm->c_cc[VTIME] = 0;
LOGPRINT("Flush terminal.\n");
// flush terminal
tcflush(fd, TCIOFLUSH);
LOGPRINT("Apply parameters.\n");
return WRAPSYSCALL(tcsetattr(fd, TCSANOW, pterm));
Additionally i set the following on file descriptor with fnctl:
int flags = fcntl(fd, F_GETFL);
fcntl(fd, F_SETFL, flags | FASYNC | O_DIRECT);
I am reading from file descriptor in a cycle with select() call on file descriptor set containing fd, then reading all bytes avaiable (requesting number of bytes much bigger then 10).
What should i change to ensure incoming data are processed as they come properly, in timely manner?
If your program does nothing else than waiting for bytes and answering, then you can try using blocking file operations. Remove O_NONBLOCK flag from your open function call, and after setting the port just do a read(fd, buffer, 10). The function will return after it reads exactly 10 bytes (or an error happens or signal arrives).
However, bear in mind that you read operation can start in the middle of packet transmission, so for example you can get last x bytes of n-th packet and first 10-x of packet n+1.
I am having some trouble reading some data from a serial port I opened the following way. I've used this instance of code plenty of times and all worked fine, but now, for some reason that I cant figure out, I am completely unable to read anything from the serial port.
I am able to write and all is correctly received on the other end, but the replies (which are correctly sent) are never received (No, the cables are all ok ;) )
The code I used to open the serial port is the following:
fd = open("/dev/ttyUSB0", O_RDWR | O_NONBLOCK | O_NOCTTY);
if (fd == -1)
{
Aviso("Unable to open port");
return (fd);
}
else
{
//Get the current options for the port...
bzero(&options, sizeof(options)); /* clear struct for new port settings */
tcgetattr(fd, &options);
/*-- Set baud rate -------------------------------------------------------*/
if (cfsetispeed(&options, SerialBaudInterp(BaudRate))==-1)
perror("On cfsetispeed:");
if (cfsetospeed(&options, SerialBaudInterp(BaudRate))==-1)
perror("On cfsetospeed:");
//Enable the receiver and set local mode...
options.c_cflag |= (CLOCAL | CREAD);
options.c_cflag &= ~PARENB; /* Parity disabled */
options.c_cflag &= ~CSTOPB;
options.c_cflag &= ~CSIZE; /* Mask the character size bits */
options.c_cflag |= SerialDataBitsInterp(8); /* CS8 - Selects 8 data bits */
options.c_cflag &= ~CRTSCTS; // disable hardware flow control
options.c_iflag &= ~(IXON | IXOFF | IXANY); // disable XON XOFF (for transmit and receive)
options.c_cflag |= CRTSCTS; /* enable hardware flow control */
options.c_cc[VMIN] = 0; //min carachters to be read
options.c_cc[VTIME] = 0; //Time to wait for data (tenths of seconds)
//Set the new options for the port...
tcflush(fd, TCIFLUSH);
if (tcsetattr(fd, TCSANOW, &options)==-1)
{
perror("On tcsetattr:");
}
PortOpen[ComPort] = fd;
}
return PortOpen[ComPort];
After the port is initializeed I write some stuff to it through simple write command...
int nc = write(hCom, txchar, n);
where hCom is the file descriptor (and it's ok), and (as I said) this works. But... when I do a read afterwards, I get a "Resource Temporarily Unavailable" error from errno.
I tested select to see when the file descriptor had something t read... but it always times out!
I read data like this:
ret = read(hCom, rxchar, n);
and I always get an EAGAIN and I have no idea why.
Update:
The HW is working fine! I can see that there is inbound data on the serial port because I've made a debug cable to read whats going on on another terminal. So...
I know what nonblocking should do. My question is... why isn't anything getting read!. The same setup works fine on windows, so all hardware is working fine...
This is driving me nuts! I'm sure it's something simple as hell! I even tried getting rid of O_NONBLOCK to see when I would receive something... but nothing...
Read this.
EAGAIN Non-blocking I/O has been
selected using O_NONBLOCK and no data
was immediately available for reading.
You need to check the serial terminal settings first.
use command - stty -F /dev/ttyUSB0 -a
Check that ctsrts is selected as -ctsrts
and do the other required settings with stty utility and you are done.
EAGAIN with O_NONBLOCK means there's been no data received on the port. Check that the port and cable are working properly (using minicom or some other known-good program), and that the remote really is sending some data.
see my code samples, if EAGAIN, you'd try to read again:
...
options.c_cflag &= ~PARENB;
options.c_iflag &= ~INPCK;
...
options.c_lflag &= ~(ICANON | ECHO | ECHOE | ISIG); // input
options.c_oflag &= ~OPOST; // output
...
fd = open("/dev/ttyUSB0", O_RDWR | O_NDELY | O_NOCTTY);
fcntl(fd, F_SETFL, 0);
...
int nc = write(hCom, txchar, n);
msleep(500); // wait 500ms
fcntl(hCom, F_SETFL, FNDELAY); // don't block serial read
ret = read(hCom, rxchar, n);
if (ret > 0) {
here had read n bytes or just partial data, read again if partial.
}
if (ret < 0) {
if (EAGAIN == errno) {
not a real error, just read again.
} else {
oops, errors.
}
}
...