I have LPC2148 daughter board but I am not able to dump/burn code into it, and it doesn't have any usb connector to dump code.
I read on internet by using FT232RL I can able dump code into LPC2148 but I am not able to do so.
please give me solution
thank you..!
The chip supports In-System Programming (ISP) via an on-chip boot loader ROM.
From the User Manual UM10139:
Programming of the Flash memory may be accomplished in several ways:
over the serial built-in JTAG interface, using In System Programming
(ISP) and UART0, or by means of In Application Programming (IAP)
capabilities.
The function of the FT232RL you mentioned is to act as a USB/UART bridge and is necessary primarily because modern PCs lack legacy RS-232 serial ports. You can in fact purchase a USB-Serial cable or adapter which will contain a bridge chip such as the FT232RL. Most of these use RS-232 line level signals, so you would still need an RS-232 line driver/receiver to connect then to your board (if your board has a serial port, it probably already has a line transceiver and you can connect directly to that). It is possible from specialist suppliers including FTDI themselves to get a USB cable with integrated FT232 and bare TTL level connections to connect directly to LPC2148 UART0 Rx/Tx lines.
If your board does not already expose a UART0 serial port and the necessart control to start the boot loader, a Serial Port Bootloader Interface board is available. For that you may then also need a USB/Serial adapter or a PC with a legacy serial ports.
Once you have a suitable serial connection, you will need the LPC2000 Flash Utility software to run on the PC.
The JTAG option is however faster, and more powerful since the JTAG is both a programming and debugging port. With a suitable toolchain and JTAG adapter it is possible to program and execute code with source-level PC hosted debugging including break pointing, data watching and single stepping of the code.
Related
I am trying to receive and send some data from a computer to an ATtiny816 through USB. Can an ATtiny816 microcontroller communicate with a computer through USB? If yes, how should it be connected?
I'm not sure if this is possible. ATtiny 816 don't have hardware USB so you have to write software stack by yourself. Take a look on V-USB library for AVR chips. It's software USB stack for most of AVR chips.
I have second idea, but question is for what you need USB? If you want to parse some commands from computer you may use USB-UART converter and parse commands from UART interface.
I am working on a project which contains acquisition of ECG data with the ADS1293EVM. MSP430F5529 is part of this board as well. For the communication between analog part of the board and microcontroller, I am using SPI and there is also FET Debugger from TI to program the microcontroller. Now I am printing data using printf to a terminal I/O which is part of the IAR software.
However, I would like to print ECG data to the terminal app in PC or to LabView, not in Terminal I/O in IAR software. The board is connected to the PC by USB so there is UART port in device manager. Is there any possibility?
Yes it is possible. You can push all the data on UART which is used in communication between PCB and PC. Than you can use any serial monitor for getting data displayed.
The only connection between your board and the PC is USB, so you have to implement a virtual USB COM port (CDC). TI's USB stack implements such an interface.
I have an embedded Linux solution and want to create a command service over serial USB. The idea being that when a computer connects to my embedded via USB, they see a serial device and send serial commands to me through that port and I send responses back.
I need some help in the direction to proceed. Do I need to emulate a serial device so they see me as a COM port? Is there build in Linux solutions to broadcast my details as a serial device? Are there code examples? I can see block devices connect with my embedded solution like a USB storage device. When I plug into another computer, I would like it to see me as a serial COM port.
I just need help in the direction of which path I should go down to solve this.
Thanks in advance.
What you are looking for is the Linux USB serial gadget. The Linux USB gadgets framework allows devices to behave as a variety of standard USB devices, including serial devices, Ethernet adapters, and mass storage devices.
Note that USB gadgets will only work on targets with a USB controller that can be set to operate as a USB device. Not all USB controllers and target devices are compatible with this configuration. For instance, most PCs have a host-only USB controller, and the Raspberry Pi Model B is not compatible with gadgets because it contains an embedded USB hub upstream of the USB ports. (However, the Pi Zero is fully compatible with gadgets.)
I am currently practising with USB programming on an AT91SAM9G20-Evaluation Kit. I learned much about USB devices and USB device port drivers while "playing" with the ATMEL provided USB device port projects (CDC-driver, ..).
But now I'd like to write a small driver to controll a wireless stick
which I plugged into one of the boards USB-A Host Ports.
I read a lot on Stack Overflow, the OpenHCI specification and even found some libraries on the net, but I am not sure if it's a good way to implement my own stack without any "good" knowledge in USB Host Port programming.
Is there a small and easy way to control the wireless-stick at the boards USB Host port? (like using the USART-Interfaces?).
I am also keen to hear hints on how to implement RTUSB or libUSB in to the AT91.
You can download AT91LIB version 1.9 from atmel from this page
The usb host libraries are under at91lib/usb/host. They're not the complete package you need though since they're just the OHCI driver -- you still need a USB driver and class drivers to implement what you want.
You could try an RTOS with USB Host support like rt-usb32
I am doing IO programming in C in Ubuntu. And I need the base address of the port to write data.
My laptop dont have a parallel port. So I bought a USB to Parallel port connector. I plugged in the device and its getting detected in /dev/usb/lp0
I ran "lsusb" to see the list of devices and I can see the ID also. But how can I get the base address ? For the usual hardware parallel devices, the base address is 0x0378. this address is not getting detected while using USB to Parallel device.
Please help.
A USB parallel port doesn't have a base address - it's not a meaningful concept for USB. I'm afraid the days of doing I/O on PC hardware via in and out instructions ended a few years ago, though lots of old tutorials still survive on the web.
You can write bytes to the parallel port as a character device, and these will appear on the printer port pins. The USB adapter will expect the other end to handshake data exactly like a printer. If you want to do general I/O prototyping, you're probably better off with a simple USB microcontroller like an Arduino.
Further discussion here.
If you are still interested to use this USB-to-parallel-printer device for your own bit-banging, it's important to know that their built-in firmware always allows controlling of D0..D7, INIT (as outputs), /ERR, ONL, PE (as inputs), but never for /ACK, BUSY (inputs), /STB, /AF, /SEL (outputs) pins.
And you need an 8-bit latch (e.g. 74HCT574) for catching data while strobing.
See here (https://www-user.tu-chemnitz.de/~ygu/bastelecke/PC/USB2LPT/faq#DIY)
especially for possible data rates.
Accessing from software side is a bit complicated but possible, and you may have to re-structure your software and hardware for making such adapters useable. I don't know for Linux case how to access, but IMHO you don't need to write a kernel-mode driver.