Cast from "int" to "unsigned short" after applying bitwise operator "~"

Cast from "int" to "unsigned short" after applying bitwise operator "~" - c

Static analysis tool I use raises a warning for this code :
uint16 var1 = 1U;
uint16 var2 = ~var1;
I check MISRA C 2004 rules and I find 10.5 rule :
If the bitwise operators ~ and << are applied to an operand od underlying type unsigned char or unsigned short, the result shall be immediately cast to the underlying type of the operand.
Ok, it's not a problem, implicit cast is applied (I think "cast" means implicit or explicit cast). But 10.1 rule says :
The value of an expression of integer type shall not be implicitly converted to a different underlying type the expression is complex.
An previous example of complex operation are : ~u16a
I change my code to :
uint16 var1 = 1U;
uint16 var2 = (uint16) ~var1;
And I obtain another warning : I think conversion of int negative value to unsigned int value not safe. I check C99 standard (ISO C99) § 6.3.1.3 but I don't understand if conversion of int to unsigned short are clearly specified.
In EmbeddedGurus article I read :
c = (unsigned int) a; /* Since a is positive, this cast is safe */
My questions :
Have explicit conversion from signed int to unsigned short unspecified behavior ?
If yes, how to use complement operator with unsigned short in safe way ?

The operands of the arithmetic and bitwise operators always undergo the standard promotions before the value is computed. Anything shorter than an int is promoted to either int or unsigned int, depending on the platform (i.e. depending on whether int can represent all values of the type that's being promoted).
On your platform, uint16_t is standard-promoted to int, since your int can represent all values of a uint16_t. Then the bitwise negation is applied to that int value, which is the cause of the problem.
To get a deterministic result independent of the platform, convert the value to an unsigned int yourself:
uint16_t var2 = (uint16_t) ~((unsigned int) var1);
Note that this is always correct, since unsigned int is required to be able to represent all the values of a uint16_t.

Have explicit conversion from signed int to unsigned short unspecified behavior ?
The conversion from signed to unsigned values is well specified it happens via modulo arithmetic is covered by section 6.3.1.3 Signed and unsigned integers from the C99 draft standard:
Otherwise, if the new type is unsigned, the value is converted by repeatedly adding or
subtracting one more than the maximum value that can be represented in the new type
until the value is in the range of the new type.49)
So for your case the negative number would be converted by repeatedly adding:
UMAX + 1
to the negative result until it is range of the unsigned type you are converting to.
For example the conversion of -1 to an unsigned type always results in the max unsigned value since -1 + UMAX + 1 is always UMAX.
If yes, how to use complement operator with unsigned short in safe way ?
What happens when you apply the ~ operator is that the value is bring promoted to int due to integer promotions being applied to the operand of ~. Which is covered in section 6.5.3.3 Unary arithmetic operators which says (emphasis mine):
The integer promotions are performed on the operand, and the result
has the promoted type. If the promoted type is an unsigned type, the
expression ~E is equivalent to the maximum value representable in that
type minus E.
Given the last sentence in the quoted paragraph perhaps casting to unsigned int first may lead to more intuitive results:
uint16 var2 = ~((unsigned int)var1);
and since you are required to apply an explicit cast then you end up with this:
uint16 var2 = (uint16) ~((unsigned int)var1);

Related

Comparisons with bit shifting [duplicate]

This post is meant to be used as a FAQ regarding implicit integer promotion in C, particularly implicit promotion caused by the usual arithmetic conversions and/or the integer promotions.
Example 1)
Why does this give a strange, large integer number and not 255?
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
Example 2)
Why does this give "-1 is larger than 0"?
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
Example 3)
Why does changing the type in the above example to short fix the problem?
unsigned short a = 1;
signed short b = -2;
if(a + b > 0)
puts("-1 is larger than 0"); // will not print
(These examples were intended for a 32 or 64 bit computer with 16 bit short.)

C was designed to implicitly and silently change the integer types of the operands used in expressions. There exist several cases where the language forces the compiler to either change the operands to a larger type, or to change their signedness.
The rationale behind this is to prevent accidental overflows during arithmetic, but also to allow operands with different signedness to co-exist in the same expression.
Unfortunately, the rules for implicit type promotion cause much more harm than good, to the point where they might be one of the biggest flaws in the C language. These rules are often not even known by the average C programmer and therefore cause all manner of very subtle bugs.
Typically you see scenarios where the programmer says "just cast to type x and it works" - but they don't know why. Or such bugs manifest themselves as rare, intermittent phenomena striking from within seemingly simple and straight-forward code. Implicit promotion is particularly troublesome in code doing bit manipulations, since most bit-wise operators in C come with poorly-defined behavior when given a signed operand.
Integer types and conversion rank
The integer types in C are char, short, int, long, long long and enum.
_Bool/bool is also treated as an integer type when it comes to type promotions.
All integers have a specified conversion rank. C11 6.3.1.1, emphasis mine on the most important parts:
Every integer type has an integer conversion rank defined as follows:
— No two signed integer types shall have the same rank, even if they have the same representation.
— The rank of a signed integer type shall be greater than the rank of any signed integer type with less precision.
— The rank of long long int shall be greater than the rank of long int, which shall be greater than the rank of int, which shall be greater than the rank of short int, which shall be greater than the rank of signed char.
— The rank of any unsigned integer type shall equal the rank of the corresponding signed integer type, if any.
— The rank of any standard integer type shall be greater than the rank of any extended integer type with the same width.
— The rank of char shall equal the rank of signed char and unsigned char.
— The rank of _Bool shall be less than the rank of all other standard integer types.
— The rank of any enumerated type shall equal the rank of the compatible integer type (see 6.7.2.2).
The types from stdint.h sort in here too, with the same rank as whatever type they happen to correspond to on the given system. For example, int32_t has the same rank as int on a 32 bit system.
Further, C11 6.3.1.1 specifies which types are regarded as the small integer types (not a formal term):
The following may be used in an expression wherever an int or unsigned int may
be used:
— An object or expression with an integer type (other than int or unsigned int) whose integer conversion rank is less than or equal to the rank of int and unsigned int.
What this somewhat cryptic text means in practice, is that _Bool, char and short (and also int8_t, uint8_t etc) are the "small integer types". These are treated in special ways and subject to implicit promotion, as explained below.
The integer promotions
Whenever a small integer type is used in an expression, it is implicitly converted to int which is always signed. This is known as the integer promotions or the integer promotion rule.
Formally, the rule says (C11 6.3.1.1):
If an int can represent all values of the original type (as restricted by the width, for a bit-field), the value is converted to an int; otherwise, it is converted to an unsigned int. These are called the integer promotions.
This means that all small integer types, no matter signedness, get implicitly converted to (signed) int when used in most expressions.
This text is often misunderstood as: "all small signed integer types are converted to signed int and all small, unsigned integer types are converted to unsigned int". This is incorrect. The unsigned part here only means that if we have for example an unsigned short operand, and int happens to have the same size as short on the given system, then the unsigned short operand is converted to unsigned int. As in, nothing of note really happens. But in case short is a smaller type than int, it is always converted to (signed) int, regardless of it the short was signed or unsigned!
The harsh reality caused by the integer promotions means that almost no operation in C can be carried out on small types like char or short. Operations are always carried out on int or larger types.
This might sound like nonsense, but luckily the compiler is allowed to optimize the code. For example, an expression containing two unsigned char operands would get the operands promoted to int and the operation carried out as int. But the compiler is allowed to optimize the expression to actually get carried out as an 8-bit operation, as would be expected. However, here comes the problem: the compiler is not allowed to optimize out the implicit change of signedness caused by the integer promotion because there is no way for the compiler to tell if the programmer is purposely relying on implicit promotion to happen, or if it is unintentional.
This is why example 1 in the question fails. Both unsigned char operands are promoted to type int, the operation is carried out on type int, and the result of x - y is of type int. Meaning that we get -1 instead of 255 which might have been expected. The compiler may generate machine code that executes the code with 8 bit instructions instead of int, but it may not optimize out the change of signedness. Meaning that we end up with a negative result, that in turn results in a weird number when printf("%u is invoked. Example 1 could be fixed by casting the result of the operation back to type unsigned char.
With the exception of a few special cases like ++ and sizeof operators, the integer promotions apply to almost all operations in C, no matter if unary, binary (or ternary) operators are used.
The usual arithmetic conversions
Whenever a binary operation (an operation with 2 operands) is done in C, both operands of the operator have to be of the same type. Therefore, in case the operands are of different types, C enforces an implicit conversion of one operand to the type of the other operand. The rules for how this is done are named the usual artihmetic conversions (sometimes informally referred to as "balancing"). These are specified in C11 6.3.18:
(Think of this rule as a long, nested if-else if statement and it might be easier to read :) )
6.3.1.8 Usual arithmetic conversions
Many operators that expect operands of arithmetic type cause conversions and yield result
types in a similar way. The purpose is to determine a common real type for the operands
and result. For the specified operands, each operand is converted, without change of type
domain, to a type whose corresponding real type is the common real type. Unless
explicitly stated otherwise, the common real type is also the corresponding real type of
the result, whose type domain is the type domain of the operands if they are the same,
and complex otherwise. This pattern is called the usual arithmetic conversions:
First, if the corresponding real type of either operand is long double, the other operand is converted, without change of type domain, to a type whose corresponding real type is long double.
Otherwise, if the corresponding real type of either operand is double, the other operand is converted, without change of type domain, to a type whose corresponding real type is double.
Otherwise, if the corresponding real type of either operand is float, the other operand is converted, without change of type domain, to a type whose corresponding real type is float.
Otherwise, the integer promotions are performed on both operands. Then the
following rules are applied to the promoted operands:
If both operands have the same type, then no further conversion is needed.
Otherwise, if both operands have signed integer types or both have unsigned
integer types, the operand with the type of lesser integer conversion rank is
converted to the type of the operand with greater rank.
Otherwise, if the operand that has unsigned integer type has rank greater or
equal to the rank of the type of the other operand, then the operand with
signed integer type is converted to the type of the operand with unsigned
integer type.
Otherwise, if the type of the operand with signed integer type can represent
all of the values of the type of the operand with unsigned integer type, then
the operand with unsigned integer type is converted to the type of the
operand with signed integer type.
Otherwise, both operands are converted to the unsigned integer type
corresponding to the type of the operand with signed integer type.
Notable here is that the usual arithmetic conversions apply to both floating point and integer variables. In the case of integers, we can also note that the integer promotions are invoked from within the usual arithmetic conversions. And after that, when both operands have at least the rank of int, the operators are balanced to the same type, with the same signedness.
This is the reason why a + b in example 2 gives a strange result. Both operands are integers and they are at least of rank int, so the integer promotions do not apply. The operands are not of the same type - a is unsigned int and b is signed int. Therefore the operator b is temporarily converted to type unsigned int. During this conversion, it loses the sign information and ends up as a large value.
The reason why changing type to short in example 3 fixes the problem, is because short is a small integer type. Meaning that both operands are integer promoted to type int which is signed. After integer promotion, both operands have the same type (int), no further conversion is needed. And then the operation can be carried out on a signed type as expected.

According to the previous post, I want to give more information about each example.
Example 1)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since unsigned char is smaller than int, we apply the integer promotion on them, then we have (int)x-(int)y = (int)(-1) and unsigned int (-1) = 4294967295.
The output from the above code:(same as what we expected)
4294967295
-1
How to fix it?
I tried what the previous post recommended, but it doesn't really work.
Here is the code based on the previous post:
change one of them to unsigned int
int main(){
unsigned int x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since x is already an unsigned integer, we only apply the integer promotion to y. Then we get (unsigned int)x-(int)y. Since they still don't have the same type, we apply the usual arithmetic converions, we get (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
Similarly, the following code gets the same result:
int main(){
unsigned char x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
change both of them to unsigned int
int main(){
unsigned int x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since both of them are unsigned int, no integer promotion is needed. By the usual arithmetic converison(have the same type), (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
One of possible ways to fix the code:(add a type cast in the end)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
unsigned char z = x-y;
printf("%u\n", z);
}
The output from the above code:
4294967295
-1
255
Example 2)
int main(){
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
printf("%u\n", a+b);
}
Since both of them are integers, no integer promotion is needed. By the usual arithmetic conversion, we get (unsigned int)a+(unsigned int)b = 1+4294967294 = 4294967295.
The output from the above code:(same as what we expected)
-1 is larger than 0
4294967295
How to fix it?
int main(){
unsigned int a = 1;
signed int b = -2;
signed int c = a+b;
if(c < 0)
puts("-1 is smaller than 0");
printf("%d\n", c);
}
The output from the above code:
-1 is smaller than 0
-1
Example 3)
int main(){
unsigned short a = 1;
signed short b = -2;
if(a + b < 0)
puts("-1 is smaller than 0");
printf("%d\n", a+b);
}
The last example fixed the problem since a and b both converted to int due to the integer promotion.
The output from the above code:
-1 is smaller than 0
-1
If I got some concepts mixed up, please let me know. Thanks~

Integer and floating point rank and promotion rules in C and C++
I'd like to take a stab at this to summarize the rules so I can quickly reference them. I've fully studied the question and both of the other two answers here, including the main one by #Lundin. If you want more examples beyond the ones below, go study that answer in detail as well, while referencing my "rules" and "promotion flow" summaries below.
I've also written my own example and demo code here: integer_promotion_overflow_underflow_undefined_behavior.c.
Despite normally being incredibly verbose myself, I'm going to try to keep this a short summary, since the other two answers plus my test code already have sufficient detail via their necessary verbosity.
Integer and variable promotion quick reference guide and summary
3 simple rules
For any operation where multiple operands (input variables) are involved (ex: mathematical operations, comparisons, or ternary), the variables are promoted as required to the required variable type before the operation is performed.
Therefore, you must manually, explicitly cast the output to any desired type you desire if you do not want it to be implicitly chosen for you. See the example below.
All types smaller than int (int32_t on my 64-bit Linux system) are "small types". They cannot be used in ANY operation. So, if all input variables are "small types", they are ALL first promoted to int (int32_t on my 64-bit Linux system) before performing the operation.
Otherwise, if at least one of the input types is int or larger, the other, smaller input type or types are promoted to this largest-input-type's type.
Example
Example: with this code:
uint8_t x = 0;
uint8_t y = 1;
...if you do x - y, they first get implicitly promoted to int (which is int32_t on my 64-bit
system), and you end up with this: (int)x - (int)y, which results in an int type with value
-1, rather than a uint8_t type of value 255. To get the desired 255 result, manually
cast the result back to uint8_t, by doing this: (uint8_t)(x - y).
Promotion flow
The promotion rules are as follows. Promotion from smallest to largest types is as follows.
Read "-->" as "gets promoted to".
The types in square brackets (ex: [int8_t]) are the typical "fixed-width integer types" for the given standard type on a typical 64-bit Unix (Linux or Mac) architecture. See, for example:
https://www.cs.yale.edu/homes/aspnes/pinewiki/C(2f)IntegerTypes.html
https://www.ibm.com/docs/en/ibm-mq/7.5?topic=platforms-standard-data-types
And even better, test it for yourself on your machine by running my code here!: stdint_sizes.c from my eRCaGuy_hello_world repo.
1. For integer types
Note: "small types" = bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t].
SMALL TYPES: bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t]
--> int [int32_t]
--> unsigned int [uint32_t]
--> long int [int64_t]
--> unsigned long int [uint64_t]
--> long long int [int64_t]
--> unsigned long long int [uint64_t]
Pointers (ex: void*) and size_t are both 64-bits, so I imagine they fit into the uint64_t category above.
2. For floating point types
float [32-bits] --> double [64-bits] --> long double [128-bits]

I would like to add two clarifications to #Lundin's otherwise excellent answer, regarding example 1, where there are two operands of identical integer type, but are "small types" that require integer promotion.
I'm using the N1256 draft since I don't have access to a paid copy of the C standard.
First: (normative)
6.3.1.1's definition of integer promotion isn't the triggering clause of actually doing integer promotion. In reality it is 6.3.1.8 Usual arithmetic conversions.
Most of the time, the "usual arithmetic conversions" apply when the operands are of different types, in which case at least one operand must be promoted. But the catch is that for integer types, integer promotion is required in all cases.
[clauses of floating-point types come first]
Otherwise, the integer promotions are performed on both operands. Then the
following rules are applied to the promoted operands:
If both operands have the same type, then no further conversion is needed.
Otherwise, if both operands have signed integer types or both have unsigned
integer types, the operand with the type of lesser integer conversion rank is
converted to the type of the operand with greater rank.
Otherwise, if the operand that has unsigned integer type has rank greater or
equal to the rank of the type of the other operand, then the operand with
signed integer type is converted to the type of the operand with unsigned
integer type.
Otherwise, if the type of the operand with signed integer type can represent
all of the values of the type of the operand with unsigned integer type, then
the operand with unsigned integer type is converted to the type of the
operand with signed integer type.
Otherwise, both operands are converted to the unsigned integer type
corresponding to the type of the operand with signed integer type.
Second: (non-normative)
There is an explicit example cited by the standard to demonstrate this:
EXAMPLE 2 In executing the fragment
char c1, c2;
/* ... */
c1 = c1 + c2;
the "integer promotions" require that the abstract machine promote the value of each variable to int size
and then add the two ints and truncate the sum. Provided the addition of two chars can be done without
overflow, or with overflow wrapping silently to produce the correct result, the actual execution need only
produce the same result, possibly omitting the promotions.

Mechanics of addition type conversion in C [duplicate]

This post is meant to be used as a FAQ regarding implicit integer promotion in C, particularly implicit promotion caused by the usual arithmetic conversions and/or the integer promotions.
Example 1)
Why does this give a strange, large integer number and not 255?
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
Example 2)
Why does this give "-1 is larger than 0"?
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
Example 3)
Why does changing the type in the above example to short fix the problem?
unsigned short a = 1;
signed short b = -2;
if(a + b > 0)
puts("-1 is larger than 0"); // will not print
(These examples were intended for a 32 or 64 bit computer with 16 bit short.)

According to the previous post, I want to give more information about each example.
Example 1)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since unsigned char is smaller than int, we apply the integer promotion on them, then we have (int)x-(int)y = (int)(-1) and unsigned int (-1) = 4294967295.
The output from the above code:(same as what we expected)
4294967295
-1
How to fix it?
I tried what the previous post recommended, but it doesn't really work.
Here is the code based on the previous post:
change one of them to unsigned int
int main(){
unsigned int x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since x is already an unsigned integer, we only apply the integer promotion to y. Then we get (unsigned int)x-(int)y. Since they still don't have the same type, we apply the usual arithmetic converions, we get (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
Similarly, the following code gets the same result:
int main(){
unsigned char x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
change both of them to unsigned int
int main(){
unsigned int x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since both of them are unsigned int, no integer promotion is needed. By the usual arithmetic converison(have the same type), (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
One of possible ways to fix the code:(add a type cast in the end)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
unsigned char z = x-y;
printf("%u\n", z);
}
The output from the above code:
4294967295
-1
255
Example 2)
int main(){
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
printf("%u\n", a+b);
}
Since both of them are integers, no integer promotion is needed. By the usual arithmetic conversion, we get (unsigned int)a+(unsigned int)b = 1+4294967294 = 4294967295.
The output from the above code:(same as what we expected)
-1 is larger than 0
4294967295
How to fix it?
int main(){
unsigned int a = 1;
signed int b = -2;
signed int c = a+b;
if(c < 0)
puts("-1 is smaller than 0");
printf("%d\n", c);
}
The output from the above code:
-1 is smaller than 0
-1
Example 3)
int main(){
unsigned short a = 1;
signed short b = -2;
if(a + b < 0)
puts("-1 is smaller than 0");
printf("%d\n", a+b);
}
The last example fixed the problem since a and b both converted to int due to the integer promotion.
The output from the above code:
-1 is smaller than 0
-1
If I got some concepts mixed up, please let me know. Thanks~

Integer and floating point rank and promotion rules in C and C++
I'd like to take a stab at this to summarize the rules so I can quickly reference them. I've fully studied the question and both of the other two answers here, including the main one by #Lundin. If you want more examples beyond the ones below, go study that answer in detail as well, while referencing my "rules" and "promotion flow" summaries below.
I've also written my own example and demo code here: integer_promotion_overflow_underflow_undefined_behavior.c.
Despite normally being incredibly verbose myself, I'm going to try to keep this a short summary, since the other two answers plus my test code already have sufficient detail via their necessary verbosity.
Integer and variable promotion quick reference guide and summary
3 simple rules
For any operation where multiple operands (input variables) are involved (ex: mathematical operations, comparisons, or ternary), the variables are promoted as required to the required variable type before the operation is performed.
Therefore, you must manually, explicitly cast the output to any desired type you desire if you do not want it to be implicitly chosen for you. See the example below.
All types smaller than int (int32_t on my 64-bit Linux system) are "small types". They cannot be used in ANY operation. So, if all input variables are "small types", they are ALL first promoted to int (int32_t on my 64-bit Linux system) before performing the operation.
Otherwise, if at least one of the input types is int or larger, the other, smaller input type or types are promoted to this largest-input-type's type.
Example
Example: with this code:
uint8_t x = 0;
uint8_t y = 1;
...if you do x - y, they first get implicitly promoted to int (which is int32_t on my 64-bit
system), and you end up with this: (int)x - (int)y, which results in an int type with value
-1, rather than a uint8_t type of value 255. To get the desired 255 result, manually
cast the result back to uint8_t, by doing this: (uint8_t)(x - y).
Promotion flow
The promotion rules are as follows. Promotion from smallest to largest types is as follows.
Read "-->" as "gets promoted to".
The types in square brackets (ex: [int8_t]) are the typical "fixed-width integer types" for the given standard type on a typical 64-bit Unix (Linux or Mac) architecture. See, for example:
https://www.cs.yale.edu/homes/aspnes/pinewiki/C(2f)IntegerTypes.html
https://www.ibm.com/docs/en/ibm-mq/7.5?topic=platforms-standard-data-types
And even better, test it for yourself on your machine by running my code here!: stdint_sizes.c from my eRCaGuy_hello_world repo.
1. For integer types
Note: "small types" = bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t].
SMALL TYPES: bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t]
--> int [int32_t]
--> unsigned int [uint32_t]
--> long int [int64_t]
--> unsigned long int [uint64_t]
--> long long int [int64_t]
--> unsigned long long int [uint64_t]
Pointers (ex: void*) and size_t are both 64-bits, so I imagine they fit into the uint64_t category above.
2. For floating point types
float [32-bits] --> double [64-bits] --> long double [128-bits]

Type of expression's result in C... Integer Promotion and Usual Conversions [duplicate]

This post is meant to be used as a FAQ regarding implicit integer promotion in C, particularly implicit promotion caused by the usual arithmetic conversions and/or the integer promotions.
Example 1)
Why does this give a strange, large integer number and not 255?
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
Example 2)
Why does this give "-1 is larger than 0"?
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
Example 3)
Why does changing the type in the above example to short fix the problem?
unsigned short a = 1;
signed short b = -2;
if(a + b > 0)
puts("-1 is larger than 0"); // will not print
(These examples were intended for a 32 or 64 bit computer with 16 bit short.)

According to the previous post, I want to give more information about each example.
Example 1)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since unsigned char is smaller than int, we apply the integer promotion on them, then we have (int)x-(int)y = (int)(-1) and unsigned int (-1) = 4294967295.
The output from the above code:(same as what we expected)
4294967295
-1
How to fix it?
I tried what the previous post recommended, but it doesn't really work.
Here is the code based on the previous post:
change one of them to unsigned int
int main(){
unsigned int x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since x is already an unsigned integer, we only apply the integer promotion to y. Then we get (unsigned int)x-(int)y. Since they still don't have the same type, we apply the usual arithmetic converions, we get (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
Similarly, the following code gets the same result:
int main(){
unsigned char x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
change both of them to unsigned int
int main(){
unsigned int x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since both of them are unsigned int, no integer promotion is needed. By the usual arithmetic converison(have the same type), (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
One of possible ways to fix the code:(add a type cast in the end)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
unsigned char z = x-y;
printf("%u\n", z);
}
The output from the above code:
4294967295
-1
255
Example 2)
int main(){
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
printf("%u\n", a+b);
}
Since both of them are integers, no integer promotion is needed. By the usual arithmetic conversion, we get (unsigned int)a+(unsigned int)b = 1+4294967294 = 4294967295.
The output from the above code:(same as what we expected)
-1 is larger than 0
4294967295
How to fix it?
int main(){
unsigned int a = 1;
signed int b = -2;
signed int c = a+b;
if(c < 0)
puts("-1 is smaller than 0");
printf("%d\n", c);
}
The output from the above code:
-1 is smaller than 0
-1
Example 3)
int main(){
unsigned short a = 1;
signed short b = -2;
if(a + b < 0)
puts("-1 is smaller than 0");
printf("%d\n", a+b);
}
The last example fixed the problem since a and b both converted to int due to the integer promotion.
The output from the above code:
-1 is smaller than 0
-1
If I got some concepts mixed up, please let me know. Thanks~

Integer and floating point rank and promotion rules in C and C++
I'd like to take a stab at this to summarize the rules so I can quickly reference them. I've fully studied the question and both of the other two answers here, including the main one by #Lundin. If you want more examples beyond the ones below, go study that answer in detail as well, while referencing my "rules" and "promotion flow" summaries below.
I've also written my own example and demo code here: integer_promotion_overflow_underflow_undefined_behavior.c.
Despite normally being incredibly verbose myself, I'm going to try to keep this a short summary, since the other two answers plus my test code already have sufficient detail via their necessary verbosity.
Integer and variable promotion quick reference guide and summary
3 simple rules
For any operation where multiple operands (input variables) are involved (ex: mathematical operations, comparisons, or ternary), the variables are promoted as required to the required variable type before the operation is performed.
Therefore, you must manually, explicitly cast the output to any desired type you desire if you do not want it to be implicitly chosen for you. See the example below.
All types smaller than int (int32_t on my 64-bit Linux system) are "small types". They cannot be used in ANY operation. So, if all input variables are "small types", they are ALL first promoted to int (int32_t on my 64-bit Linux system) before performing the operation.
Otherwise, if at least one of the input types is int or larger, the other, smaller input type or types are promoted to this largest-input-type's type.
Example
Example: with this code:
uint8_t x = 0;
uint8_t y = 1;
...if you do x - y, they first get implicitly promoted to int (which is int32_t on my 64-bit
system), and you end up with this: (int)x - (int)y, which results in an int type with value
-1, rather than a uint8_t type of value 255. To get the desired 255 result, manually
cast the result back to uint8_t, by doing this: (uint8_t)(x - y).
Promotion flow
The promotion rules are as follows. Promotion from smallest to largest types is as follows.
Read "-->" as "gets promoted to".
The types in square brackets (ex: [int8_t]) are the typical "fixed-width integer types" for the given standard type on a typical 64-bit Unix (Linux or Mac) architecture. See, for example:
https://www.cs.yale.edu/homes/aspnes/pinewiki/C(2f)IntegerTypes.html
https://www.ibm.com/docs/en/ibm-mq/7.5?topic=platforms-standard-data-types
And even better, test it for yourself on your machine by running my code here!: stdint_sizes.c from my eRCaGuy_hello_world repo.
1. For integer types
Note: "small types" = bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t].
SMALL TYPES: bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t]
--> int [int32_t]
--> unsigned int [uint32_t]
--> long int [int64_t]
--> unsigned long int [uint64_t]
--> long long int [int64_t]
--> unsigned long long int [uint64_t]
Pointers (ex: void*) and size_t are both 64-bits, so I imagine they fit into the uint64_t category above.
2. For floating point types
float [32-bits] --> double [64-bits] --> long double [128-bits]

Implicit type promotion rules

This post is meant to be used as a FAQ regarding implicit integer promotion in C, particularly implicit promotion caused by the usual arithmetic conversions and/or the integer promotions.
Example 1)
Why does this give a strange, large integer number and not 255?
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
Example 2)
Why does this give "-1 is larger than 0"?
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
Example 3)
Why does changing the type in the above example to short fix the problem?
unsigned short a = 1;
signed short b = -2;
if(a + b > 0)
puts("-1 is larger than 0"); // will not print
(These examples were intended for a 32 or 64 bit computer with 16 bit short.)

According to the previous post, I want to give more information about each example.
Example 1)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since unsigned char is smaller than int, we apply the integer promotion on them, then we have (int)x-(int)y = (int)(-1) and unsigned int (-1) = 4294967295.
The output from the above code:(same as what we expected)
4294967295
-1
How to fix it?
I tried what the previous post recommended, but it doesn't really work.
Here is the code based on the previous post:
change one of them to unsigned int
int main(){
unsigned int x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since x is already an unsigned integer, we only apply the integer promotion to y. Then we get (unsigned int)x-(int)y. Since they still don't have the same type, we apply the usual arithmetic converions, we get (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
Similarly, the following code gets the same result:
int main(){
unsigned char x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
change both of them to unsigned int
int main(){
unsigned int x = 0;
unsigned int y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
}
Since both of them are unsigned int, no integer promotion is needed. By the usual arithmetic converison(have the same type), (unsigned int)x-(unsigned int)y = 4294967295.
The output from the above code:(same as what we expected):
4294967295
-1
One of possible ways to fix the code:(add a type cast in the end)
int main(){
unsigned char x = 0;
unsigned char y = 1;
printf("%u\n", x - y);
printf("%d\n", x - y);
unsigned char z = x-y;
printf("%u\n", z);
}
The output from the above code:
4294967295
-1
255
Example 2)
int main(){
unsigned int a = 1;
signed int b = -2;
if(a + b > 0)
puts("-1 is larger than 0");
printf("%u\n", a+b);
}
Since both of them are integers, no integer promotion is needed. By the usual arithmetic conversion, we get (unsigned int)a+(unsigned int)b = 1+4294967294 = 4294967295.
The output from the above code:(same as what we expected)
-1 is larger than 0
4294967295
How to fix it?
int main(){
unsigned int a = 1;
signed int b = -2;
signed int c = a+b;
if(c < 0)
puts("-1 is smaller than 0");
printf("%d\n", c);
}
The output from the above code:
-1 is smaller than 0
-1
Example 3)
int main(){
unsigned short a = 1;
signed short b = -2;
if(a + b < 0)
puts("-1 is smaller than 0");
printf("%d\n", a+b);
}
The last example fixed the problem since a and b both converted to int due to the integer promotion.
The output from the above code:
-1 is smaller than 0
-1
If I got some concepts mixed up, please let me know. Thanks~

Integer and floating point rank and promotion rules in C and C++
I'd like to take a stab at this to summarize the rules so I can quickly reference them. I've fully studied the question and both of the other two answers here, including the main one by #Lundin. If you want more examples beyond the ones below, go study that answer in detail as well, while referencing my "rules" and "promotion flow" summaries below.
I've also written my own example and demo code here: integer_promotion_overflow_underflow_undefined_behavior.c.
Despite normally being incredibly verbose myself, I'm going to try to keep this a short summary, since the other two answers plus my test code already have sufficient detail via their necessary verbosity.
Integer and variable promotion quick reference guide and summary
3 simple rules
For any operation where multiple operands (input variables) are involved (ex: mathematical operations, comparisons, or ternary), the variables are promoted as required to the required variable type before the operation is performed.
Therefore, you must manually, explicitly cast the output to any desired type you desire if you do not want it to be implicitly chosen for you. See the example below.
All types smaller than int (int32_t on my 64-bit Linux system) are "small types". They cannot be used in ANY operation. So, if all input variables are "small types", they are ALL first promoted to int (int32_t on my 64-bit Linux system) before performing the operation.
Otherwise, if at least one of the input types is int or larger, the other, smaller input type or types are promoted to this largest-input-type's type.
Example
Example: with this code:
uint8_t x = 0;
uint8_t y = 1;
...if you do x - y, they first get implicitly promoted to int (which is int32_t on my 64-bit
system), and you end up with this: (int)x - (int)y, which results in an int type with value
-1, rather than a uint8_t type of value 255. To get the desired 255 result, manually
cast the result back to uint8_t, by doing this: (uint8_t)(x - y).
Promotion flow
The promotion rules are as follows. Promotion from smallest to largest types is as follows.
Read "-->" as "gets promoted to".
The types in square brackets (ex: [int8_t]) are the typical "fixed-width integer types" for the given standard type on a typical 64-bit Unix (Linux or Mac) architecture. See, for example:
https://www.cs.yale.edu/homes/aspnes/pinewiki/C(2f)IntegerTypes.html
https://www.ibm.com/docs/en/ibm-mq/7.5?topic=platforms-standard-data-types
And even better, test it for yourself on your machine by running my code here!: stdint_sizes.c from my eRCaGuy_hello_world repo.
1. For integer types
Note: "small types" = bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t].
SMALL TYPES: bool (_Bool), char [int8_t], unsigned char [uint8_t], short [int16_t], unsigned short [uint16_t]
--> int [int32_t]
--> unsigned int [uint32_t]
--> long int [int64_t]
--> unsigned long int [uint64_t]
--> long long int [int64_t]
--> unsigned long long int [uint64_t]
Pointers (ex: void*) and size_t are both 64-bits, so I imagine they fit into the uint64_t category above.
2. For floating point types
float [32-bits] --> double [64-bits] --> long double [128-bits]

Is conversion from unsigned to signed undefined?

void fun(){
signed int a=-5;
unsigned int b=-5;
printf("the value of b is %u\n",b);
if(a==b)
printf("same\n");
else
printf("diff");
}
It is printing :
4294967291
same
In the 2nd line signed value is converted to unsigned value. So b has the value UINTMAX + 1 - 5 = 4294967291.
My question is what is happening in the comparison operation .
1) Is a again converted to unsigned and compared with b ?
2) Will b(ie unsigned ) be ever casted to signed value and compared automatically?
3) Is conversion from unsigned to signed undefined due to int overflow ?
I have read other posts on the topic. I just want clarification on questions 2 and 3 .

1) Is a again converted to unsigned and compared with b ?
Yes. In the expression (a==b), the implicit type conversion called "balancing" takes place (the formal name is "the usual arithmetic conversions"). Balancing rules specify that if a signed and a unsigned operand of the same size and type are compared, the signed operand is converted to a unsigned.
2) Will b(ie unsigned ) be ever casted to signed value and compared automatically?
No, it will never be converted to signed in your example.
3) Is conversion from unsigned to signed undefined due to int overflow ?
This is what the standard says: (C11)
6.3.1.3 Signed and unsigned integers
1 When a value with integer type is converted to another integer type
other than _Bool, if the value can be represented by the new type, it
is unchanged.
2 Otherwise, if the new type is unsigned, the value is
converted by repeatedly adding or subtracting one more than the
maximum value that can be represented in the new type until the value
is in the range of the new type.
3 Otherwise, the new type is
signed and the value cannot be represented in it; either the result is
implementation-defined or an implementation-defined signal is raised.
In other words, if the compiler can manage to do the conversion in 2) above, then the behavior is well-defined. If it cannot, then the result depends on the compiler implementation.
It is not undefined behavior.

Answers:
a is converted to unsigned int.
If a had a wider range than the signed counterpart of b (I can imagine long long a would do), b would be converted to a signed type.
If an unsigned value can't be correctly represented after conversion to a signed type, you'll have implementation-defined behavior. If it can, no problem.

b = -5;
That counts as overflow and is undefined behavior. Comparing signed with unsigned automatically promotes the operands to unsigned. -In case of overflow, you'll find yourself again in a case of undefined behavior.- plain wrong, see [edit] below
See also http://c-faq.com/expr/preservingrules.html.
[edit] Correction - the standard does state that the 2 complement should be used when converting from negative signed to unsigned.

Develop Reference

c reactjs sql-server angularjs arrays wpf database batch-file google-app-engine silverlight