Related
I wrote a simple C-code to compute average of N floats that exist in an array. I got 10.5 ClockCyles per float as throughput for large N.
arm_mean_f32() is actually poorer in performance.
Isn't this too many CCs/float?
The 3 operations
load-from-memory
accumulation-of-loaded-values
increment of pointer
can happen in parallel.
Does ARM Cortex M4F do this?
The project was run on custom board with Freescale K24 processor having ARM Cortex M4F.
ARM implementation is very traditional you can check it on Github , they just do loop unrolling to reduce loop overhead then accumulate the sum of 4 samples each loop and finally divide the number of samples, i tried it with M4F and i got 5.3 cycles per float.
Here is the code i used
#include "arm_math.h"
#define MAX_BLOCKSIZE 32
float32_t src_buf_f32[MAX_BLOCKSIZE] =
{
-0.4325648115282207, -1.6655843782380970, 0.1253323064748307,
0.2876764203585489, -1.1464713506814637, 1.1909154656429988,
1.1891642016521031, -0.0376332765933176, 0.3272923614086541,
0.1746391428209245, -0.1867085776814394, 0.7257905482933027,
-0.5883165430141887, 2.1831858181971011, -0.1363958830865957,
0.1139313135208096, 1.0667682113591888, 0.0592814605236053,
-0.0956484054836690, -0.8323494636500225, 0.2944108163926404,
-1.3361818579378040, 0.7143245518189522, 1.6235620644462707,
-0.6917757017022868, 0.8579966728282626, 1.2540014216025324,
-1.5937295764474768, -1.4409644319010200, 0.5711476236581780,
-0.3998855777153632, 0.6899973754643451
};
float32_t result_f32;
int main(void)
{
arm_mean_f32(src_buf_f32, MAX_BLOCKSIZE, &result_f32);
return 0;
}
I think this is the best performance you can get with floating point, your poor performance can be due to that your are measuring the number of cycles incorrectly or your silicon. you can also try to increase compiler optimization.
I need to optimize some for-loops for speed (for a school assignment) without using compiler optimization flags.
Given a specific Linux server (owned by the school), a satisfactory improvement is to make it run under 7 seconds, and a great improvement is to make it run under 5 seconds. This code that I have right here gets about 5.6 seconds. I am thinking I may need to use pointers with this in some way to get it to go faster, but I'm not really sure. What options do I have?
The file must remain 50 lines or less (not counting comments).
#include <stdio.h>
#include <stdlib.h>
// You are only allowed to make changes to this code as specified by the comments in it.
// The code you submit must have these two values.
#define N_TIMES 600000
#define ARRAY_SIZE 10000
int main(void)
{
double *array = calloc(ARRAY_SIZE, sizeof(double));
double sum = 0;
int i;
// You can add variables between this comment ...
register double sum1 = 0, sum2 = 0, sum3 = 0, sum4 = 0, sum5 = 0, sum6 = 0, sum7 = 0, sum8 = 0, sum9 = 0;
register int j;
// ... and this one.
printf("CS201 - Asgmt 4 - \n");
for (i = 0; i < N_TIMES; i++)
{
// You can change anything between this comment ...
for (j = 0; j < ARRAY_SIZE; j += 10)
{
sum += array[j];
sum1 += array[j + 1];
sum2 += array[j + 2];
sum3 += array[j + 3];
sum4 += array[j + 4];
sum5 += array[j + 5];
sum6 += array[j + 6];
sum7 += array[j + 7];
sum8 += array[j + 8];
sum9 += array[j + 9];
}
// ... and this one. But your inner loop must do the same
// number of additions as this one does.
}
// You can add some final code between this comment ...
sum += sum1 + sum2 + sum3 + sum4 + sum5 + sum6 + sum7 + sum8 + sum9;
// ... and this one.
return 0;
}
Re-posting a modified version of my answer from optimized sum of an array of doubles in C, since that question got voted down to -5. The OP of the other question phrased it more as "what else is possible", so I took him at his word and info-dumped about vectorizing and tuning for current CPU hardware. :)
The OP of that question eventually said he wasn't allowed to use compiler options higher than -O0, which I guess is the case here, too.
Summary:
Why using -O0 distorts things (unfairly penalizes things that are fine in normal code for a normal compiler). Using -O0 (the gcc/clang default) so your loops don't optimize away is not a valid excuse or a useful way to find out what will be faster with normal optimization enabled. (See also Idiomatic way of performance evaluation? for more about benchmark methods and pitfalls, like ways to enable optimization but still stop the compiler from optimizing away the work you want to measure.)
Stuff that's wrong with the assignment.
Types of optimizations. FP latency vs. throughput, and dependency chains. Link to Agner Fog's site. (Essential reading for optimization).
Experiments getting the compiler to optimize it (after fixing it to not optimize away). Best result with auto-vectorization (no source changes): gcc: half as fast as an optimal vectorized loop. clang: same speed as a hand-vectorized loop.
Some more comments on why bigger expressions are a perf win with -O0 only.
Source changes to get good performance without -ffast-math, making the code closer to what we want the compiler to do. Also some rules-lawyering ideas that would be useless in the real-world.
Vectorizing the loop with GCC architecture-neutral vectors, to see how close the auto-vectorizing compilers came to matching the performance of ideal asm code (since I checked the compiler output).
I think the point of the assignment is to sort of teach assembly-language performance optimizations using C with no compiler optimizations. This is silly. It's mixing up things the compiler will do for you in real life with things that do require source-level changes.
See Why does clang produce inefficient asm with -O0 (for this simple floating point sum)?
-O0 doesn't just "not optimize", it makes the compiler store variables to memory after every statement instead of keeping them in registers. It does this so you get the "expected" results if you set a breakpoint with gdb and modify the value (in memory) of a C variable. Or even if you jump to another line in the same function. So each C statement has to be compiled to an independent block of asm that starts and ends with all variables in memory. For a modern portable compiler like gcc which already transforms through multiple internal representations of program flow on the way from source to asm, this part of -O0 requires explicitly de-optimizing its graph of data flow back into separate C statements. These store/reloads lengthen every loop-carried dependency chain so it's horrible for tiny loops if the loop counter is kept in memory. (e.g. 1 cycle per iteration for inc reg vs. 6c for inc [mem], creating a bottleneck on loop counter updates in tight loops).
With gcc -O0, the register keyword lets gcc keep a var in a register instead of memory, and thus can make a big difference in tight loops (Example on the Godbolt Compiler explorer). But that's only with -O0. In real code, register is meaningless: the compiler attempts to optimally use the available registers for variables and temporaries. register is already deprecated in ISO C++11 (but not C11), and there's a proposal to remove it from the language along with other obsolete stuff like trigraphs.
With an extra variables involved, -O0 hurts array indexing a bit more than pointer incrementing.
Array indexing usually makes code easier to read. Compilers sometimes fail to optimize stuff like array[i*width + j*width*height], so it's a good idea to change the source to do the strength-reduction optimization of turning the multiplies into += adds.
At an asm level, array indexing vs. pointer incrementing are close to the same performance. (x86 for example has addressing modes like [rsi + rdx*4] which are as fast as [rdi]. except on Sandybridge and later.) It's the compiler's job to optimize your code by using pointer incrementing even when the source uses array indexing, when that's faster.
For good performance, you have to be aware of what compilers can and can't do. Some optimizations are "brittle", and a small seemingly-innocent change to the source will stop the compiler from doing an optimization that was essential for some code to run fast. (e.g. pulling a constant computation out of a loop, or proving something about how different branch conditions are related to each other, and simplifying.)
Besides all that, it's a crap sample because it doesn't have anything to stop a smart compiler from optimizing away the entire thing. It doesn't even print the sum. Even gcc -O1 (instead of -O3) threw away some of the looping.
(You can fix this by printing sum at the end. gcc and clang don't seem to realize that calloc returns zeroed memory, and optimize it away to 0.0. See my code below.)
Normally you'd put your code in a function, and call it in a loop from main() in another file. And compile them separately, without whole-program cross-file optimisation, so the compiler can't do optimisations based on the compile-time constants you call it with. The repeat-loop being wrapped so tightly around the actual loop over the array is causing havoc with gcc's optimizer (see below).
Also, the other version of this question had an uninitialized variable kicking around. It looks like long int help was introduced by the OP of that question, not the prof. So I will have to downgrade my "utter nonsense" to merely "silly", because the code doesn't even print the result at the end. That's the most common way of getting the compiler not to optimize everything away in a microbenchmark like this.
I assume your prof mentioned a few things about performance. There are a crapton of different things that could come into play here, many of which I assume didn't get mentioned in a 2nd-year CS class.
Besides multithreading with openmp, there's vectorizing with SIMD. There are also optimizations for modern pipelined CPUs: specifically, avoid having one long dependency chain.
Further essential reading:
Agner Fog's guides for optimizing C and asm for x86. Some of it applies to all CPUs.
What Every Programmer Should Know About Memory
Your compiler manual is also essential, esp. for floating point code. Floating point has limited precision, and is not associative. The final sum does depend on which order you do the additions in. Usually the difference in rounding error is small, so the compiler can get a big speedup by re-ordering things if you use -ffast-math to allow it.
Instead of just unrolling, keep multiple accumulators which you only add up at the end, like you're doing with the sum0..sum9 unroll-by-10. FP instructions have medium latency but high throughput, so you need to keep multiple FP operations in flight to keep the floating point execution units saturated.
If you need the result of the last op to be complete before the next one can start, you're limited by latency. For FP add, that's one per 3 cycles. In Intel Sandybridge, IvB, Haswell, and Broadwell, the throughput of FP add is one per cycle. So you need to keep at least 3 independent ops that can be in flight at once to saturate the machine. For Skylake, it's 2 per cycle with latency of 4 clocks. (On the plus side for Skylake, FMA is down to 4 cycle latency.)
In this case, there's also basic stuff like pulling things out of the loop, e.g. help += ARRAY_SIZE.
Compiler Options
Lets start by seeing what the compiler can do for us.
I started out with the original inner loop, with just help += ARRAY_SIZE pulled out, and adding a printf at the end so gcc doesn't optimize everything away. Let's try some compiler options and see what we can achieve with gcc 4.9.2 (on my i5 2500k Sandybridge. 3.8GHz max turbo (slight OC), 3.3GHz sustained (irrelevant for this short benchmark)):
gcc -O0 fast-loop-cs201.c -o fl: 16.43s performance is a total joke. Variables are stored to memory after every operation, and re-loaded before the next. This is a bottleneck, and adds a lot of latency. Not to mention losing out on actual optimisations. Timing / tuning code with -O0 is not useful.
-O1: 4.87s
-O2: 4.89s
-O3: 2.453s (uses SSE to do 2 at once. I'm of course using a 64bit system, so hardware support for -msse2 is baseline.)
-O3 -ffast-math -funroll-loops: 2.439s
-O3 -march=sandybridge -ffast-math -funroll-loops: 1.275s (uses AVX to do 4 at once.)
-Ofast ...: no gain
-O3 -ftree-parallelize-loops=4 -march=sandybridge -ffast-math -funroll-loops: 0m2.375s real, 0m8.500s user. Looks like locking overhead killed it. It only spawns the 4 threads total, but the inner loop is too short for it to be a win: it collects the sums every time, instead of giving each thread 1/4 of the outer loop iterations.
-Ofast -fprofile-generate -march=sandybridge -ffast-math, run it, then
-Ofast -fprofile-use -march=sandybridge -ffast-math: 1.275s. profile-guided optimization is a good idea when you can exercise all the relevant code-paths, so the compiler can make better unrolling / inlining decisions.
clang-3.5 -Ofast -march=native -ffast-math: 1.070s. (clang 3.5 is too old to support -march=sandybridge. You should prefer to use a compiler version that's new enough to know about the target architecture you're tuning for, esp. if using -march to make code that doesn't need to run on older architectures.)
gcc -O3 vectorizes in a hilarious way: The inner loop does 2 (or 4) iterations of the outer loop in parallel, by broadcasting one array element to all elements of an xmm (or ymm) register, and doing an addpd on that. So it sees the same values are being added repeatedly, but even -ffast-math doesn't let gcc just turn it into a multiply. Or switch the loops.
clang-3.5 vectorizes a lot better: it vectorizes the inner loop, instead of the outer, so it doesn't need to broadcast. It even uses 4 vector registers as 4 separate accumulators. It knows that calloc only returns 16-byte aligned memory (on x86-64 System V), and when tuning for Sandybridge (before Haswell) it knows that 32-byte loads have a big penalty when misaligned. And that splitting them isn't too expensive since a 32-byte load takes 2 cycles in a load port anyway.
vmovupd -0x60(%rbx,%rcx,8),%xmm4
vinsertf128 $0x1,-0x50(%rbx,%rcx,8),%ymm4,%ymm4
This is worse on later CPUs, especially when the data does happen to be aligned at run-time; see Why doesn't gcc resolve _mm256_loadu_pd as single vmovupd? about GCC versions where -mavx256-split-unaligned-load was on by default with -mtune=generic.
It's actually slower when I tell it that the array is aligned. (with a stupid hack like array = (double*)((ptrdiff_t)array & ~31); which actually generates an instruction to mask off the low 5 bits, because clang-3.5 doesn't support gcc's __builtin_assume_aligned.) In that case it uses a tight loop of 4x vaddpd mem, %ymm, %ymm. It only runs about 0.65 insns per cycle (and 0.93 uops / cycle), according to perf, so the bottleneck isn't front-end.
I checked with a debugger, and calloc is indeed returning a pointer that's an odd multiple of 16. (glibc for large allocations tends to allocate new pages, and put bookkeeping info in the initial bytes, always misaligning to any boundary wider than 16.) So half the 32B memory accesses are crossing a cache line, causing a big slowdown. It is slightly faster to do two separate 16B loads when your pointer is 16B-aligned but not 32B-aligned, on Sandybridge. (gcc enables -mavx256-split-unaligned-load and ...-store for -march=sandybridge, and also for the default tune=generic with -mavx, which is not so good especially for Haswell or with memory that's usually aligned by the compiler doesn't know about it.)
Source level changes
As we can see from clang beating gcc, multiple accumulators are excellent. The most obvious way to do this would be:
for (j = 0; j < ARRAY_SIZE; j+=4) { // unroll 4 times
sum0 += array[j];
sum1 += array[j+1];
sum2 += array[j+2];
sum3 += array[j+3];
}
and then don't collect the 4 accumulators into one until after the end of the outer loop.
Your (from the other question) source change of
sum += j[0]+j[1]+j[2]+j[3]+j[4]+j[5]+j[6]+j[7]+j[8]+j[9];
actually has a similar effect, thanks to out-of-order execution. Each group of 10 is a separate dependency chain. order-of-operations rules say the j values get added together first, and then added to sum. So the loop-carried dependency chain is still only the latency of one FP add, and there's lots of independent work for each group of 10. Each group is a separate dependency chain of 9 adds, and takes few enough instructions for the out-of-order execution hardware to see the start of the next chain and, and find the parallelism to keep those medium latency, high throughput FP execution units fed.
With -O0, as your silly assignment apparently requires, values are stored to RAM at the end of every statement. Writing longer expressions without updating any variables, even temporaries, will make -O0 run faster, but it's not a useful optimisation. Don't waste your time on changes that only help with -O0, esp. not at the expense of readability.
Using 4 accumulator variables and not adding them together until the end of the outer loop defeats clang's auto-vectorizer. It still runs in only 1.66s (vs. 4.89 for gcc's non-vectorized -O2 with one accumulator). Even gcc -O2 without -ffast-math also gets 1.66s for this source change. Note that ARRAY_SIZE is known to be a multiple of 4, so I didn't include any cleanup code to handle the last up-to-3 elements (or to avoid reading past the end of the array, which would happen as written now). It's really easy to get something wrong and read past the end of the array when doing this.
GCC, on the other hand, does vectorize this, but it also pessimises (un-optimises) the inner loop into a single dependency chain. I think it's doing multiple iterations of the outer loop, again.
Using gcc's platform-independent vector extensions, I wrote a version which compiles into apparently-optimal code:
// compile with gcc -g -Wall -std=gnu11 -Ofast -fno-tree-vectorize -march=native fast-loop-cs201.vec.c -o fl3-vec
#include <stdio.h>
#include <stdlib.h>
#include <stddef.h>
#include <assert.h>
#include <string.h>
// You are only allowed to make changes to this code as specified by the comments in it.
// The code you submit must have these two values.
#define N_TIMES 600000
#define ARRAY_SIZE 10000
int main(void)
{
double *array = calloc(ARRAY_SIZE, sizeof(double));
double sum = 0;
int i;
// You can add variables between this comment ...
long int help = 0;
typedef double v4df __attribute__ ((vector_size (8*4)));
v4df sum0={0}, sum1={0}, sum2={0}, sum3={0};
const size_t array_bytes = ARRAY_SIZE*sizeof(double);
double *aligned_array = NULL;
// this more-than-declaration could go in an if(i == 0) block for strict compliance with the rules
if ( posix_memalign((void**)&aligned_array, 32, array_bytes) ) {
exit (1);
}
memcpy(aligned_array, array, array_bytes); // In this one case: faster to align once and have no extra overhead for N_TIMES through the loop
// ... and this one.
// Please change 'your name' to your actual name.
printf("CS201 - Asgmt 4 - I. Forgot\n");
for (i = 0; i < N_TIMES; i++) {
// You can change anything between this comment ...
/*
#if defined(__GNUC__) && (__GNUC__ * 100 + __GNUC_MINOR__) >= 407 // GCC 4.7 or later.
array = __builtin_assume_aligned(array, 32);
#else
// force-align for other compilers. This loop-invariant will be done outside the loop.
array = (double*) ((ptrdiff_t)array & ~31);
#endif
*/
assert ( ARRAY_SIZE / (4*4) == (ARRAY_SIZE+15) / (4*4) ); // We don't have a cleanup loop to handle where the array size isn't a multiple of 16
// incrementing pointers can be more efficient than indexing arrays
// esp. on recent Intel where micro-fusion only works with one-register addressing modes
// of course, the compiler can always generate pointer-incrementing asm from array-indexing source
const double *start = aligned_array;
while ( (ptrdiff_t)start & 31 ) {
// annoying loops like this are the reason people use aligned buffers
sum += *start++; // scalar until we reach 32B alignment
// in practice, this loop doesn't run, because we copy into an aligned buffer
// This will also require a cleanup loop, and break our multiple-of-16 doubles assumption.
}
const v4df *end = (v4df *)(aligned_array+ARRAY_SIZE);
for (const v4df *p = (v4df *)start ; p+3 < end; p+=4) {
sum0 += p[0]; // p+=4 increments the pointer by 4 * 4 * 8 bytes
sum1 += p[1]; // make sure you keep track of what you're incrementing
sum2 += p[2];
sum3 += p[3];
}
// the compiler might be smart enough to pull this out of the inner loop
// in fact, gcc turns this into a 64bit movabs outside of both loops :P
help+= ARRAY_SIZE;
// ... and this one. But your inner loop must do the same
// number of additions as this one does.
/* You could argue legalese and say that
if (i == 0) {
for (j ...)
sum += array[j];
sum *= N_TIMES;
}
* still does as many adds in its *INNER LOOP*, but it just doesn't run it as often
*/
}
// You can add some final code between this comment ...
sum0 = (sum0 + sum1) + (sum2 + sum3);
sum += sum0[0] + sum0[1] + sum0[2] + sum0[3];
printf("sum = %g; help=%ld\n", sum, help); // defeat the compiler.
free (aligned_array);
free (array); // not strictly necessary, because this is the end of main(). Leaving it out for this special case is a bad example for a CS class, though.
// ... and this one.
return 0;
}
The inner loop compiles to:
4007c0: c5 e5 58 19 vaddpd (%rcx),%ymm3,%ymm3
4007c4: 48 83 e9 80 sub $0xffffffffffffff80,%rcx # subtract -128, because -128 fits in imm8 instead of requiring an imm32 to encode add $128, %rcx
4007c8: c5 f5 58 49 a0 vaddpd -0x60(%rcx),%ymm1,%ymm1 # one-register addressing mode can micro-fuse
4007cd: c5 ed 58 51 c0 vaddpd -0x40(%rcx),%ymm2,%ymm2
4007d2: c5 fd 58 41 e0 vaddpd -0x20(%rcx),%ymm0,%ymm0
4007d7: 4c 39 c1 cmp %r8,%rcx # compare with end with p
4007da: 75 e4 jne 4007c0 <main+0xb0>
(For more, see online compiler output at the godbolt compiler explorer. The -xc compiler option compiles as C, not C++. The inner loop is from .L3 to jne .L3. See the x86 tag wiki for x86 asm links. See also this q&a about micro-fusion not happening on SnB-family, which Agner Fog's guides don't cover).
performance:
$ perf stat -e task-clock,cycles,instructions,r1b1,r10e,stalled-cycles-frontend,stalled-cycles-backend,L1-dcache-load-misses,cache-misses ./fl3-vec
CS201 - Asgmt 4 - I. Forgot
sum = 0; help=6000000000
Performance counter stats for './fl3-vec':
1086.571078 task-clock (msec) # 1.000 CPUs utilized
4,072,679,849 cycles # 3.748 GHz
2,629,419,883 instructions # 0.65 insns per cycle
# 1.27 stalled cycles per insn
4,028,715,968 r1b1 # 3707.733 M/sec # unfused uops
2,257,875,023 r10e # 2077.982 M/sec # fused uops. lower than insns because of macro-fusion
3,328,275,626 stalled-cycles-frontend # 81.72% frontend cycles idle
1,648,011,059 stalled-cycles-backend # 40.47% backend cycles idle
751,736,741 L1-dcache-load-misses # 691.843 M/sec
18,772 cache-misses # 0.017 M/sec
1.086925466 seconds time elapsed
I still don't know why it's getting such low instructions per cycle. The inner loop is using 4 separate accumulators, and I checked with gdb that the pointers are aligned. So cache-bank conflicts shouldn't be the problem. Sandybridge L2 cache can sustain one 32B transfers per cycle, which should keep up with the one 32B FP vector add per cycle.
32B loads from L1 take 2 cycles (it wasn't until Haswell that Intel made 32B loads a single-cycle operation). However, there are 2 load ports, so the sustained throughput is 32B per cycle (which we're not reaching).
Perhaps the loads need to be pipelined ahead of when they're used, to minimize having the ROB (re-order buffer) fill up when a load stalls? But the perf counters indicate a fairly high L1 cache hit rate, so hardware prefetch from L2 to L1 seems to be doing its job.
0.65 instructions per cycle is only about half way to saturating the vector FP adder. This is frustrating. Even IACA says the loop should run in 4 cycles per iteration. (i.e. saturate the load ports and port1 (where the FP adder lives)) :/
update: I guess L2 bandwidth was the problem after all. There aren't enough line-fill buffers to keep enough misses in flight to sustain the peak throughput every cycle. L2 sustained bandwidth is less than peak on Intel SnB / Haswell / Skylake CPUs.
See also Single Threaded Memory Bandwidth on Sandy Bridge (Intel forum thread, with much discussion about what limits throughput, and how latency * max_concurrency is one possible bottleneck. See also the "Latency Bound Platforms" part of the answer to Enhanced REP MOVSB for memcpy limited memory concurrency is a bottleneck for loads as well as stores, but for loads prefetch into L2 does mean you might not be limited purely by Line Fill buffers for outstanding L1D misses.
Reducing ARRAY_SIZE to 1008 (multiple of 16), and increasing N_TIMES by a factor of 10, brought the runtime down to 0.5s. That's 1.68 insns per cycle. (The inner loop is 7 total instructions for 4 FP adds, thus we are finally saturating the vector FP add unit, and the load ports.) Loop tiling is a much better solution, see below.
Intel CPUs only have 32k each L1-data and L1-instruction caches. I think your array would just barely fit in the 64kiB L1D on an AMD K10 (Istanbul) CPU, but not Bulldozer-family (16kiB L1D) or Ryzen (32kiB L1D).
Gcc's attempt to vectorize by broadcasting the same value into a parallel add doesn't seem so crazy. If it had managed to get this right (using multiple accumulators to hide latency), that would have allowed it to saturate the vector FP adder with only half the memory bandwidth. As-is, it was pretty much a wash, probably because of overhead in broadcasting.
Also, it's pretty silly. The N_TIMES is a just a make-work repeat. We don't actually want to optimize for doing the identical work multiple times. Unless we want to win at silly assignments like this. A source-level way to do this would be to increment i in the part of the code we're allowed to modify:
for (...) {
sum += a[j] + a[j] + a[j] + a[j];
}
i += 3; // The inner loop does 4 total iterations of the outer loop
More realistically, to deal with this you could interchange your loops (loop over the array once, adding each value N_TIMES times). I think I've read that Intel's compiler will sometimes do that for you.
A more general technique is called cache blocking, or loop tiling. The idea is to work on your input data in small blocks that fit in cache. Depending on your algorithm, it can be possible to do various stages of thing on a chunk, then repeat for the next chunk, instead of having each stage loop over the whole input. As always, once you know the right name for a trick (and that it exists at all), you can google up a ton of info.
You could rules-lawyer your way into putting an interchanged loop inside an if (i == 0) block in the part of the code you're allowed to modify. It would still do the same number of additions, but in a more cache-optimal order.
You may be on the right track, though you'll need to measure it to be certain (my normal advice to measure, not guess seems a little superfluous here since the whole point of the assignment is to measure).
Optimising compilers will probably not see much of a difference since they're pretty clever about that sort of stuff but, since we don't know what optimisation level it will be compiling at, you may get a substantial improvement.
To use pointers in the inner loop is a simple matter of first adding a pointer variable:
register double *pj;
then changing the loop to:
for (pj = &(array[0]); pj < &(array[ARRAY_SIZE]); j++) {
sum += *j++;
sum1 += *j++;
sum2 += *j++;
sum3 += *j++;
sum4 += *j++;
sum5 += *j++;
sum6 += *j++;
sum7 += *j++;
sum8 += *j++;
sum9 += *j;
}
This keeps the amount of additions the same within the loop (assuming you're counting += and ++ as addition operators, of course) but basically uses pointers rather than array indexes.
With no optimisation1 on my system, this drops it from 9.868 seconds (CPU time) to 4.84 seconds. Your mileage may vary.
1 With optimisation level -O3, both are reported as taking 0.001 seconds so, as mentioned, the optimisers are pretty clever. However, given you're seeing 5+ seconds, I'd suggest it wasn't been compiled with optimisation on.
As an aside, this is a good reason why it's usually advisable to write your code in a readable manner and let the compiler take care of getting it running faster. While my meager attempts at optimisation roughly doubled the speed, using -O3 made it run some ten thousand times faster :-)
Before anything else, try to change compiler settings to produce faster code. There is general optimisation, and the compiler might do auto vectorisation.
What you would always do is try several approaches and check what is fastest. As a target, try to get to one cycle per addition or better.
Number of iterations per loop: You add up 10 sums simultaneously. It might be that your processor doesn't have enough registers for that, or it has more. I'd measure the time for 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14... sums per loop.
Number of sums: Having more than one sum means that latency doesn't bite you, just throughput. But more than four or six might not be helpful. Try four sums, with 4, 8, 12, 16 iterations per loop. Or six sums, with 6, 12, 18 iterations.
Caching: You are running through an array of 80,000 bytes. Probably more than L1 cache. Split the array into 2 or 4 parts. Do an outer loop iterating over the two or four subarrays, the next loop from 0 to N_TIMES - 1, and the inner loop adding up values.
And then you can try using vector operations, or multi-threading your code, or using the GPU to do the work.
And if you are forced to use no optimisation, then the "register" keyword might actually work.
This question already has answers here:
How to optimize these loops (with compiler optimization disabled)?
(3 answers)
Closed 5 years ago.
I've got an assignment where I must take a program and make it more efficient in terms of time.
the original code is:
#include <stdio.h>
#include <stdlib.h>
// You are only allowed to make changes to this code as specified by the comments in it.
// The code you submit must have these two values.
#define N_TIMES 600000
#define ARRAY_SIZE 10000
int main(void)
{
double *array = calloc(ARRAY_SIZE, sizeof(double));
double sum = 0;
int i;
// You can add variables between this comment ...
long int help;
// ... and this one.
// Please change 'your name' to your actual name.
printf("CS201 - Asgmt 4 - I. Forgot\n");
for (i = 0; i < N_TIMES; i++) {
// You can change anything between this comment ...
int j;
for (j = 0; j < ARRAY_SIZE; j++) {
sum += array[j];
help++;
}
// ... and this one. But your inner loop must do the same
// number of additions as this one does.
}
// You can add some final code between this comment ...
// ... and this one.
return 0;
}
I almost exclusively modified the second for loop by changing it to
double *j=array;
double *p=array+ARRAY_SIZE;
for(; j<p;j+=10){
sum += j[0]+j[1]+j[2]+j[3]+j[4]+j[5]+j[6]+j[7]+j[8]+j[9];
{
this on its own was able to reduce the time down to the criteria...
it already seems to work but are there any mistakes i'm not seeing?
I posted an improved version of this answer on a duplicate of this: C loop optimization help for final assignment. It was originally just a repost, but then I made some changes to answer the differences in that question. I forget what's different, but you should probably read that one instead. Maybe I should just delete this one.
See also other optimization guides in the x86 tag wiki.
First of all, it's a really crap sample because it doesn't have anything to stop a smart compiler from optimizing away the entire thing. It doesn't even print the sum. Even gcc -O1 (instead of -O3) threw away some of the looping.
Normally you'd put your code in a function, and call it in a loop from main() in another file. And compile them separately, without whole-program cross-file optimisation, so the compiler can't do optimisations based on the compile-time constants you call it with. The repeat-loop being wrapped so tightly around the actual loop over the array is causing havoc with gcc's optimizer (see below).
Also:
gcc -Wall -O3 -march=native fast-loop-cs201.c -o fl
fast-loop-cs201.c: In function ‘main’:
fast-loop-cs201.c:17:14: warning: ‘help’ is used uninitialized in this function [-Wuninitialized]
long int help;
I have to agree with EOF's disparaging remarks about your prof. Giving out code that optimizes away to nothing, and with uninitialized variables, is utter nonsense.
Some people are saying in comments that "the compiler doesn't matter", and that you're supposed to do optimize your C source for the CPU microarchitecture, rather than letting the compiler do it. This is crap: for good performance, you have to be aware of what compilers can do, and can't do. Some optimizations are "brittle", and a small seemingly-innocent change to the source will stop the compiler from doing something.
I assume your prof mentioned a few things about performance. There are a crapton of different things that could come into play here, many of which I assume didn't get mentioned in a 2nd-year CS class.
Besides multithreading with openmp, there's vectorizing with SIMD. There are also optimizations for modern pipelined CPUs: specifically, avoid having one long dependency chain.
Further essential reading:
Agner Fog's guides for optimizing C and asm for x86. Some of it applies to all CPUs.
What Every Programmer Should Know About Memory
Your compiler manual is also essential, esp. for floating point code. Floating point has limited precision, and is not associative. The final sum does depend on which order you do the additions in. However, usually the difference in rounding error is small. So the compiler can get a big speedup by re-ordering things if you use -ffast-math to allow it. This may have been what your unroll-by-10 allowed.
Instead of just unrolling, keeping multiple accumulators which you only add up at the end can keep the floating point execution units saturated, because FP instructions have latency != throughput. If you need the result of the last op to be complete before the next one can start, you're limited by latency. For FP add, that's one per 3 cycles. In Intel Sandybridge, IvB, Haswell, and Broadwell, the throughput of FP add is one per cycle. So you need to keep at least 3 independent ops that can be in flight at once to saturate the machine. For Skylake, it's 2 per cycle with latency of 4 clocks. (On the plus side for Skylake, FMA is down to 4 cycle latency.)
In this case, there's also basic stuff like pulling things out of the loop, e.g. help += ARRAY_SIZE.
compiler options
I started out with the original inner loop, with just help += ARRAY_SIZE pulled out, and adding a printf at the end so gcc doesn't optimize everything away. Let's try some compiler options and see what we can achieve with gcc 4.9.2 (on my i5 2500k Sandybridge. 3.8GHz max turbo (slight OC), 3.3GHz sustained (irrelevant for this short benchmark)):
gcc -O0 fast-loop-cs201.c -o fl: 16.43s performance is a total joke. Variables are stored to memory after every operation, and re-loaded before the next. This is a bottleneck, and adds a lot of latency. Not to mention losing out on actual optimisations. Timing / tuning code with -O0 is not useful.
-O1: 4.87s
-O2: 4.89s
-O3: 2.453s (uses SSE to do 2 at once. I'm of course using a 64bit system, so hardware support for -msse2 is baseline.)
-O3 -ffast-math -funroll-loops: 2.439s
-O3 -march=sandybridge -ffast-math -funroll-loops: 1.275s (uses AVX to do 4 at once.)
-Ofast ...: no gain
-O3 -ftree-parallelize-loops=4 -march=sandybridge -ffast-math -funroll-loops: 0m2.375s real, 0m8.500s user. Looks like locking overhead killed it. It only spawns the 4 threads total, but the inner loop is too short for it to be a win (because it collects the sums every time, instead of giving one thread the first 1/4 of the outer loop iterations).
-Ofast -fprofile-generate -march=sandybridge -ffast-math, run it, then
-Ofast -fprofile-use -march=sandybridge -ffast-math: 1.275s
clang-3.5 -Ofast -march=native -ffast-math: 1.070s. (clang doesn't support -march=sandybridge).
gcc -O3 vectorizes in a hilarious way: The inner loop does 2 (or 4) iterations of the outer loop in parallel, by broadcasting one array element to all elements of an xmm (or ymm) register, and doing an addpd on that. So it sees the same values are being added repeatedly, but even -ffast-math doesn't let gcc just turn it into a multiply. Or switch the loops.
clang-3.5 vectorizes a lot better: it vectorizes the inner loop, instead of the outer, so it doesn't need to broadcast. It even uses 4 vector registers as 4 separate accumulators. However, it doesn't assume that calloc returns aligned memory, and for some reason it thinks the best bet is a pair of 128b loads.
vmovupd -0x60(%rbx,%rcx,8),%xmm4`
vinsertf128 $0x1,-0x50(%rbx,%rcx,8),%ymm4,%ymm4
It's actually slower when I tell it that the array is aligned. (with a stupid hack like array = (double*)((ptrdiff_t)array & ~31); which actually generates an instruction to mask off the low 5 bits, because clang-3.5 doesn't support gcc's __builtin_assume_aligned.) I think the way the tight loop of 4x vaddpd mem, %ymmX,%ymmX is aligned puts cmp $0x271c,%rcx crossing a 32B boundary, so it can't macro-fuse with jne. uop throughput shouldn't be an issue, though, since this code is only getting 0.65insns per cycle (and 0.93 uops / cycle), according to perf.
Ahh, I checked with a debugger, and calloc is only returning a 16B-aligned pointer. So half the 32B memory accesses are crossing a cache line, causing a big slowdown. I guess it is slightly faster to do two separate 16B loads when your pointer is 16B-aligned but not 32B-aligned, on Sandybridge. The compiler is making a good choice here.
Source level changes
As we can see from clang beating gcc, multiple accumulators are excellent. The most obvious way to do this would be:
for (j = 0; j < ARRAY_SIZE; j+=4) { // unroll 4 times
sum0 += array[j];
sum1 += array[j+1];
sum2 += array[j+2];
sum3 += array[j+3];
}
and then don't collect the 4 accumulators into one until after the end of the outer loop.
Your source change of
sum += j[0]+j[1]+j[2]+j[3]+j[4]+j[5]+j[6]+j[7]+j[8]+j[9];
actually has a similar effect, thanks to out-of-order execution. Each group of 10 is a separate dependency chain. order-of-operations rules say the j values get added together first, and then added to sum. So the loop-carried dependency chain is still only the latency of one FP add, and there's lots of independent work for each group of 10. Each group is a separate dependency chain of 9 adds, and takes few enough instructions for the out-of-order execution hardware to see the start of the next chain and, and find the parallelism to keep those medium latency, high throughput FP execution units fed.
With -O0, as your silly assignment apparently requires, values are stored to RAM at the end of every statement. (Technically, at every "sequence point", as the C standards call it.) Writing longer expressions without updating any variables, even temporaries, will make -O0 run faster, but it's not a useful optimisation. Don't waste your time on changes that only help with -O0, esp. not at the expense of readability.
Using 4-accumulators and not adding them together until the end of the outer loop defeats clang's auto-vectorizer. It still runs in only 1.66s (vs. 4.89 for gcc's non-vectorized -O2 with one accumulator). Even gcc -O2 without -ffast-math also gets 1.66s for this source change. Note that ARRAY_SIZE is known to be a multiple of 4, so I didn't include any cleanup code to handle the last up-to-3 elements (or to avoid reading past the end of the array, which would happen as written now). It's really easy to get something wrong and read past the end of the array when doing this.
gcc, on the other hand, does vectorize this, but it also pessimises (un-optimises) the inner loop into a single dependency chain. I think it's doing multiple iterations of the outer loop, again.
Using gcc's platform-independent vector extensions, I wrote a version which compiles into apparently-optimal code:
// compile with gcc -g -Wall -std=gnu11 -Ofast -fno-tree-vectorize -march=native fast-loop-cs201.vec.c -o fl3-vec
#include <stdio.h>
#include <stdlib.h>
#include <stddef.h>
#include <assert.h>
#include <string.h>
// You are only allowed to make changes to this code as specified by the comments in it.
// The code you submit must have these two values.
#define N_TIMES 600000
#define ARRAY_SIZE 10000
int main(void)
{
double *array = calloc(ARRAY_SIZE, sizeof(double));
double sum = 0;
int i;
// You can add variables between this comment ...
long int help = 0;
typedef double v4df __attribute__ ((vector_size (8*4)));
v4df sum0={0}, sum1={0}, sum2={0}, sum3={0};
const size_t array_bytes = ARRAY_SIZE*sizeof(double);
double *aligned_array = NULL;
// this more-than-declaration could go in an if(i == 0) block for strict compliance with the rules
if ( posix_memalign((void**)&aligned_array, 32, array_bytes) ) {
exit (1);
}
memcpy(aligned_array, array, array_bytes); // In this one case: faster to align once and have no extra overhead for N_TIMES through the loop
// ... and this one.
// Please change 'your name' to your actual name.
printf("CS201 - Asgmt 4 - I. Forgot\n");
for (i = 0; i < N_TIMES; i++) {
// You can change anything between this comment ...
/*
#if defined(__GNUC__) && (__GNUC__ * 100 + __GNUC_MINOR__) >= 407 // GCC 4.7 or later.
array = __builtin_assume_aligned(array, 32);
#else
// force-align for other compilers. This loop-invariant will be done outside the loop.
array = (double*) ((ptrdiff_t)array & ~31);
#endif
*/
assert ( ARRAY_SIZE / (4*4) == (ARRAY_SIZE+15) / (4*4) ); // We don't have a cleanup loop to handle where the array size isn't a multiple of 16
// incrementing pointers can be more efficient than indexing arrays
// esp. on recent Intel where micro-fusion only works with one-register addressing modes
// of course, the compiler can always generate pointer-incrementing asm from array-indexing source
const double *start = aligned_array;
while ( (ptrdiff_t)start & 31 ) {
// annoying loops like this are the reason people use aligned buffers
sum += *start++; // scalar until we reach 32B alignment
// in practice, this loop doesn't run, because we copy into an aligned buffer
// This will also require a cleanup loop, and break our multiple-of-16 doubles assumption.
}
const v4df *end = (v4df *)(aligned_array+ARRAY_SIZE);
for (const v4df *p = (v4df *)start ; p+3 < end; p+=4) {
sum0 += p[0]; // p+=4 increments the pointer by 4 * 4 * 8 bytes
sum1 += p[1]; // make sure you keep track of what you're incrementing
sum2 += p[2];
sum3 += p[3];
}
// the compiler might be smart enough to pull this out of the inner loop
// in fact, gcc turns this into a 64bit movabs outside of both loops :P
help+= ARRAY_SIZE;
// ... and this one. But your inner loop must do the same
// number of additions as this one does.
/* You could argue legalese and say that
if (i == 0) {
for (j ...)
sum += array[j];
sum *= N_TIMES;
}
* still does as many adds in its *INNER LOOP*, but it just doesn't run it as often
*/
}
// You can add some final code between this comment ...
sum0 = (sum0 + sum1) + (sum2 + sum3);
sum += sum0[0] + sum0[1] + sum0[2] + sum0[3];
printf("sum = %g; help=%ld\n", sum, help); // defeat the compiler.
free (aligned_array);
free (array); // not strictly necessary, because this is the end of main(). Leaving it out for this special case is a bad example for a CS class, though.
// ... and this one.
return 0;
}
The inner loop compiles to:
4007c0: c5 e5 58 19 vaddpd (%rcx),%ymm3,%ymm3
4007c4: 48 83 e9 80 sub $0xffffffffffffff80,%rcx # subtract -128, because -128 fits in imm8 instead of requiring an imm32 to encode add $128, %rcx
4007c8: c5 f5 58 49 a0 vaddpd -0x60(%rcx),%ymm1,%ymm1 # one-register addressing mode can micro-fuse
4007cd: c5 ed 58 51 c0 vaddpd -0x40(%rcx),%ymm2,%ymm2
4007d2: c5 fd 58 41 e0 vaddpd -0x20(%rcx),%ymm0,%ymm0
4007d7: 4c 39 c1 cmp %r8,%rcx # compare with end with p
4007da: 75 e4 jne 4007c0 <main+0xb0>
(For more, see online compiler output at godbolt. Note I had to cast the return value of calloc, because godbolt uses C++ compilers, not C compilers. The inner loop is from .L3 to jne .L3. See https://stackoverflow.com/tags/x86/info for x86 asm links. See also Micro fusion and addressing modes, because this Sandybridge change hasn't made it into Agner Fog's manuals yet.).
performance:
$ perf stat -e task-clock,cycles,instructions,r1b1,r10e,stalled-cycles-frontend,stalled-cycles-backend,L1-dcache-load-misses,cache-misses ./fl3-vec
CS201 - Asgmt 4 - I. Forgot
sum = 0; help=6000000000
Performance counter stats for './fl3-vec':
1086.571078 task-clock (msec) # 1.000 CPUs utilized
4,072,679,849 cycles # 3.748 GHz
2,629,419,883 instructions # 0.65 insns per cycle
# 1.27 stalled cycles per insn
4,028,715,968 r1b1 # 3707.733 M/sec # unfused uops
2,257,875,023 r10e # 2077.982 M/sec # fused uops. lower than insns because of macro-fusion
3,328,275,626 stalled-cycles-frontend # 81.72% frontend cycles idle
1,648,011,059 stalled-cycles-backend # 40.47% backend cycles idle
751,736,741 L1-dcache-load-misses # 691.843 M/sec
18,772 cache-misses # 0.017 M/sec
1.086925466 seconds time elapsed
I still don't know why it's getting such low instructions per cycle. The inner loop is using 4 separate accumulators, and I checked with gdb that the pointers are aligned. So cache-bank conflicts shouldn't be the problem. Sandybridge L2 cache can sustain one 32B transfers per cycle, which should keep up with the one 32B FP vector add per cycle.
Loads 32B loads from L1 take 2 cycles (it wasn't until Haswell that Intel made 32B loads a single-cycle operation). However, there are 2 load ports, so the sustained throughput is 32B per cycle (which we're not reaching).
Perhaps the loads need to be pipelined ahead of when they're used, to minimize having the ROB (re-order buffer) fill up when a load stalls? But the perf counters indicate a fairly high L1 cache hit rate, so hardware prefetch from L2 to L1 seems to be doing its job.
0.65 instructions per cycle is only about half way to saturating the vector FP adder. This is frustrating. Even IACA says the loop should run in 4 cycles per iteration. (i.e. saturate the load ports and port1 (where the FP adder lives)) :/
update: I guess L2 latency was the problem after all. Reducing ARRAY_SIZE to 1008 (multiple of 16), and increasing N_TIMES by a factor of 10, brought the runtime down to 0.5s. That's 1.68 insns per cycle. (The inner loop is 7 total instructions for 4 FP adds, thus we are finally saturating the vector FP add unit, and the load ports.) IDK why the HW prefetcher can't get ahead after one stall, and then stay ahead. Possibly software prefetch could help? Maybe somehow avoid having the HW prefetcher run past the array, and instead start prefetching the start of the array again. (loop tiling is a much better solution, see below.)
Intel CPUs only have 32k each L1-data and L1-instruction caches. I think your array would just barely fit in the L1 on an AMD CPU.
Gcc's attempt to vectorize by broadcasting the same value into a parallel add doesn't seem so crazy. If it had managed to get this right (using multiple accumulators to hide latency), that would have allowed it to saturate the vector FP adder with only half the memory bandwidth. As-is, it was pretty much a wash, probably because of overhead in broadcasting.
Also, it's pretty silly. The N_TIMES is a just a make-work repeat. We don't actually want to optimize for doing the identical work multiple times. Unless we want to win at silly assignments like this. A source-level way to do this would be to increment i in the part of the code we're allowed to modify:
for (...) {
sum += a[j] + a[j] + a[j] + a[j];
}
i += 3; // The inner loop does 4 total iterations of the outer loop
More realistically, to deal with this you could interchange your loops (loop over the array once, adding each value N_TIMES times). I think I've read that Intel's compiler will sometimes do that for you.
A more general technique is called cache blocking, or loop tiling. The idea is to work on your input data in small blocks that fit in cache. Depending on your algorithm, it can be possible to do various stages of thing on a chunk, then repeat for the next chunk, instead of having each stage loop over the whole input. As always, once you know the right name for a trick (and that it exists at all), you can google up a ton of info.
You could rules-lawyer your way into putting an interchanged loop inside an if (i == 0) block in the part of the code you're allowed to modify. It would still do the same number of additions, but in a more cache-optimal order.
I would try this for the inner loop:
double* tmp = array;
for (j = 0; j < ARRAY_SIZE; j++) {
sum += *tmp; // Use a pointer
tmp++; // because it is faster to increment the pointer
// than it is to recalculate array+j every time
help++;
}
or better
double* tmp = array;
double* end = array + ARRAY_SIZE; // Get rid of variable j by calculating
// the end criteria and
while (tmp != end) { // just compare if the end is reached
sum += *tmp;
tmp++;
help++;
}
I think You should read about openmp library if You could use multithreaded. But this is so simple example that I think could not be optimized.
Certain thing is that You don't need to declare i and j before for loop. That would do:
for (int i = 0; i < N_TIMES; i++)
I'm converting SSE2 sine and cosine functions (from Julien Pommier's sse_mathfun.h; based on the CEPHES sinf function) to use AVX in order to accept 8 float vectors or 4 doubles.
So, Julien's function sin_ps becomes sin_ps8 (for 8 floats) and sin_pd4 for 4 doubles. (The "advanced" editor here fails to accept my code, so please visit http://arstechnica.com/civis/viewtopic.php?f=20&t=1227375 to see it.)
Testing with clang 3.3 under Mac OS X 10.6.8 running on a 2011 Core2 i7 # 2.7Ghz, benchmarking results look like this:
sinf .. -> 27.7 millions of vector evaluations/second over 5.56e+07
iters (standard, scalar sinf() function)
sin_ps .. -> 41.0 millions of vector evaluations/second over
8.22e+07 iters
sin_pd4 .. -> 40.2 millions of vector evaluations/second over
8.06e+07 iters
sin_ps8 .. -> 2.5 millions of vector evaluations/second over
5.1e+06 iters
The cost of sin_ps8 is downright frightening, and it seems it is due to the use of _mm256_castsi256_ps . In fact, commenting out the line "poly_mask = _mm256_castsi256_ps(emmm2);" results in a more normal performance.
sin_pd4 uses _mm_castsi128_pd, but it appears that is not (just) the mix of SSE and AVX instructions that is biting me in sin_ps8: when I emulate the _mm256_castsi256_ps calls with 2 calls to _mm_castsi128_ps, performance doesn't improve. emm2 and emm0 are pointers to emmm2 and emmm0, both v8si instances and thus (a priori) correctly aligned to 32 bits boundaries.
See sse_mathfun.h and sse_mathfun_test.c for compilable code.
Is there a(n easy) way to avoid the penalty I'm seeing?
Transferring stuff out of registers into memory isn't usually a good idea. You are doing this every time you store into a pointer.
Instead of this:
{ ALIGN32_BEG v4sf *yy ALIGN32_END = (v4sf*) &y;
emm2[0] = _mm_and_si128(_mm_add_epi32( _mm_cvttps_epi32( yy[0] ), _v4si_pi32_1), _v4si_pi32_inv1),
emm2[1] = _mm_and_si128(_mm_add_epi32( _mm_cvttps_epi32( yy[1] ), _v4si_pi32_1), _v4si_pi32_inv1);
yy[0] = _mm_cvtepi32_ps(emm2[0]),
yy[1] = _mm_cvtepi32_ps(emm2[1]);
}
/* get the swap sign flag */
emm0[0] = _mm_slli_epi32(_mm_and_si128(emm2[0], _v4si_pi32_4), 29),
emm0[1] = _mm_slli_epi32(_mm_and_si128(emm2[1], _v4si_pi32_4), 29);
/* get the polynom selection mask
there is one polynom for 0 <= x <= Pi/4
and another one for Pi/4<x<=Pi/2
Both branches will be computed.
*/
emm2[0] = _mm_cmpeq_epi32(_mm_and_si128(emm2[0], _v4si_pi32_2), _mm_setzero_si128()),
emm2[1] = _mm_cmpeq_epi32(_mm_and_si128(emm2[1], _v4si_pi32_2), _mm_setzero_si128());
((v4sf*)&poly_mask)[0] = _mm_castsi128_ps(emm2[0]);
((v4sf*)&poly_mask)[1] = _mm_castsi128_ps(emm2[1]);
swap_sign_bit = _mm256_castsi256_ps(emmm0);
Try something like this:
__m128i emm2a = _mm_and_si128(_mm_add_epi32( _mm256_castps256_ps128(y), _v4si_pi32_1), _v4si_pi32_inv1);
__m128i emm2b = _mm_and_si128(_mm_add_epi32( _mm256_extractf128_ps(y, 1), _v4si_pi32_1), _v4si_pi32_inv1);
y = _mm256_insertf128_ps(_mm256_castps128_ps256(_mm_cvtepi32_ps(emm2a)), _mm_cvtepi32_ps(emm2b), 1);
/* get the swap sign flag */
__m128i emm0a = _mm_slli_epi32(_mm_and_si128(emm2a, _v4si_pi32_4), 29),
__m128i emm0b = _mm_slli_epi32(_mm_and_si128(emm2b, _v4si_pi32_4), 29);
swap_sign_bit = _mm256_castsi256_ps(_mm256_insertf128_si256(_mm256_castsi128_si256(emm0a), emm0b, 1));
/* get the polynom selection mask
there is one polynom for 0 <= x <= Pi/4
and another one for Pi/4<x<=Pi/2
Both branches will be computed.
*/
emm2a = _mm_cmpeq_epi32(_mm_and_si128(emm2a, _v4si_pi32_2), _mm_setzero_si128()),
emm2b = _mm_cmpeq_epi32(_mm_and_si128(emm2b, _v4si_pi32_2), _mm_setzero_si128());
poly_mask = _mm256_castsi256_ps(_mm256_insertf128_si256(_mm256_castsi128_si256(emm2a), emm2b, 1));
As mentioned in comments, cast intrinsics are purely compile-time and emit no instructions.
Maybe you could compare your code to the already working AVX extension of Julien Pommier SSE math functions?
http://software-lisc.fbk.eu/avx_mathfun/
This code works in GCC but not MSVC and only supports floats (float8) but I think you could easily extend it to use doubles (double4) as well. A quick comparison of your sin function shows that they are quite similar except for the SSE2 integer part.
I am working on a code in which at two places there are 64bit by 32 bit fixed point division and the result is taken in 32 bits. These two places are together taking more than 20% of my total time taken. So I feel like if I could remove the 64 bit division, I could optimize the code well. In NEON we can have some 64 bit instructions. Can any one suggest some routine to get the bottleneck resolved by using some faster implementation.
Or if I could make the 64 bit/32 bit division in terms of 32bit/32 bit division in C, that also is fine?
If any one has some idea, could you please help me out?
I did a lot of fixed-point arithmetic in the past and did a lot of research looking for fast 64/32 bit divisions myself. If you google for 'ARM division' you will find tons of great links and discussion about this issue.
The best solution for ARM architecture, where even a 32 bit division may not be available in hardware is here:
http://www.peter-teichmann.de/adiv2e.html
This assembly code is very old, and your assembler may not understand the syntax of it. It is however worth porting the code to your toolchain. It is the fastest division code for your special case I've seen so far, and trust me: I've benchmarked them all :-)
Last time I did that (about 5 years ago, for CortexA8) this code was about 10 times faster than what the compiler generated.
This code doesn't use NEON. A NEON port would be interesting. Not sure if it will improve the performance much though.
Edit:
I found the code with assembler ported to GAS (GNU Toolchain). This code is working and tested:
Divide.S
.section ".text"
.global udiv64
udiv64:
adds r0,r0,r0
adc r1,r1,r1
.rept 31
cmp r1,r2
subcs r1,r1,r2
adcs r0,r0,r0
adc r1,r1,r1
.endr
cmp r1,r2
subcs r1,r1,r2
adcs r0,r0,r0
bx lr
C-Code:
extern "C" uint32_t udiv64 (uint32_t a, uint32_t b, uint32_t c);
int32_t fixdiv24 (int32_t a, int32_t b)
/* calculate (a<<24)/b with 64 bit immediate result */
{
int q;
int sign = (a^b) < 0; /* different signs */
uint32_t l,h;
a = a<0 ? -a:a;
b = b<0 ? -b:b;
l = (a << 24);
h = (a >> 8);
q = udiv64 (l,h,b);
if (sign) q = -q;
return q;
}