I am programming a MAX32 Micro controller in MPLAB. I want to use the UART protocol to interact with my terminal (I am developing on a mac). Is this possible? Can someone point me in the right direction to get started?
Read Wikipedia UART Article
Read Reference Manual of your µC, Chapter "...UART..."
Get example Code for this issue from your Reference Manual or Programming Manual or Internet Articles
Program your board
Connect your Board with your PC via Cable (USB, RS232 to USB (virtual RS232) or UART to USB)
Open Terminal Program i.e. TeraTerm
Check your Settings i.e. Baud Rate
Try it
Related
I am trying to learn Linux by following instructions in "Mastering Embedded Linux Programming" by Chris Simmonds. By following the book and with some help from Stack_Overflow_1, i was able to build the MLO and u-boot.img.
However, when i connect USB cable to my PC and execute the ls /dev/tty* command, i cannot find any device with /dev/ttyUSB. All i can see are devices with /dev/tty0-63, /dev/ttyS0-31 and one /dev/ttyprintk.
Also, when i press down the S2 button and connect the USB cable, i can only see the power led glowing and nothing else.
I have properly built the u-boot (three attempts to get it right).
Also, as per the instructions in the book, i am only testing the u-boot stuff and yet to reach the kernal part.
If i remove the sd card and connect the USB, im an able to talk to my BBB over ssh (192.168.7.2).
How to i get the u-boot to work? Thank you!
If you don't have one yet, I'd recommend to get a USB-to-serial device (3.3V Vref). You connect it to the debug UART (J1) which is located next to the P9 side. Nowadays those are very cheap and can cost below 1$. Ones that feature a genuine FTDI part will be 5-10$ at least.
The serial port you are referencing is only available once the device has passed through U-Boot, booted the kernel and finally userspace has set up the communications.
Especially when working with U-Boot and the Kernel, low level UART access is crucial.
As a further note, could it be that the Book refers to the (white) original Beaglebone? That has a FTDI USB-to-UART chip on board and will allow you even U-Boot access. You can do the same things if you have the above mentioned USB device.
https://groups.google.com/g/beagleboard/c/eNDjK05spY8/m/GPvhcP52BAAJ shows that one needs to hold the space key to enter u-boot.
Also, the info. here might be more up to date compared to the book.
https://www.digikey.com/eewiki/display/linuxonarm/BeagleBone+Black
There is no way to copy and paste everything from the eewiki. I just left you the link. Enjoy!
I am working on a project which contains acquisition of ECG data with the ADS1293EVM. MSP430F5529 is part of this board as well. For the communication between analog part of the board and microcontroller, I am using SPI and there is also FET Debugger from TI to program the microcontroller. Now I am printing data using printf to a terminal I/O which is part of the IAR software.
However, I would like to print ECG data to the terminal app in PC or to LabView, not in Terminal I/O in IAR software. The board is connected to the PC by USB so there is UART port in device manager. Is there any possibility?
Yes it is possible. You can push all the data on UART which is used in communication between PCB and PC. Than you can use any serial monitor for getting data displayed.
The only connection between your board and the PC is USB, so you have to implement a virtual USB COM port (CDC). TI's USB stack implements such an interface.
I have LPC2148 daughter board but I am not able to dump/burn code into it, and it doesn't have any usb connector to dump code.
I read on internet by using FT232RL I can able dump code into LPC2148 but I am not able to do so.
please give me solution
thank you..!
The chip supports In-System Programming (ISP) via an on-chip boot loader ROM.
From the User Manual UM10139:
Programming of the Flash memory may be accomplished in several ways:
over the serial built-in JTAG interface, using In System Programming
(ISP) and UART0, or by means of In Application Programming (IAP)
capabilities.
The function of the FT232RL you mentioned is to act as a USB/UART bridge and is necessary primarily because modern PCs lack legacy RS-232 serial ports. You can in fact purchase a USB-Serial cable or adapter which will contain a bridge chip such as the FT232RL. Most of these use RS-232 line level signals, so you would still need an RS-232 line driver/receiver to connect then to your board (if your board has a serial port, it probably already has a line transceiver and you can connect directly to that). It is possible from specialist suppliers including FTDI themselves to get a USB cable with integrated FT232 and bare TTL level connections to connect directly to LPC2148 UART0 Rx/Tx lines.
If your board does not already expose a UART0 serial port and the necessart control to start the boot loader, a Serial Port Bootloader Interface board is available. For that you may then also need a USB/Serial adapter or a PC with a legacy serial ports.
Once you have a suitable serial connection, you will need the LPC2000 Flash Utility software to run on the PC.
The JTAG option is however faster, and more powerful since the JTAG is both a programming and debugging port. With a suitable toolchain and JTAG adapter it is possible to program and execute code with source-level PC hosted debugging including break pointing, data watching and single stepping of the code.
How can I communicate with an mbed LPC1768 using C without using a terminal emulator like minicom or teraterm?
For example if I send an integer from my C code than that led should be turned on.
How can I do this?
Without reading user manual or datasheet you can't do any thing to your board. So just go through it then follow below link for demo application LPC1768 board
1.NXP LPC1768 ARM Cortex-M3 Red Suite Demo
2.LPC1768 ARM Cortex-M3 CrossWorks Demo
3.mbed
4.At github
If you are using linux or osx check out the following answer:
How do I read data from serial port in Linux using C?
You can check your /dev folder and look for a file that is created when you plug your mBed. The file name would be something like /dev/ttyS0. That file represents the communication port, you can read/write that file to receive/send data over serial port.
If you want a cross platform solution try RxTx library for Java.
You can use this library
what it does, is that it initialize UART port which is connected to the debugger on your board and use it as serial input output. so with any hyper terminal of your choice, you can write code to do something if you send certain string of characters or just use original printf when something happens. and it will be printed on your PC screen.
I have sensor node connected to USB port that sense temperature, humidity and light and send the data to PC.
What piece of code will help me to read that data from the USB port in normal C.
Application of the nodes is built on C using Eclipse.
I looked into the specifications of your board and it seems like it's a FTDI chip. This means it's exactly the same way you read from a serial port.
Here is how you program the serial port in Windows (it hasn't changed in a long time).